微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读

This specification covers three types of drawn pure and thoriated tungsten wire suitable for fabrication into parts for electron tubes, lamps, and other electron devices, and one type of rod for metal-to-glass sealing (grid wire is excepted): Type 1A, Type 1B, Type 2A, and Type 2B. Types 1A and 1B are designated as UNS R07005; Type 2A is designated as UNS R07911; and Type 2B is designated as UNS R07912. The wire and rod shall conform to the prescribed chemical requirements for thoria and tungsten and to the specified physical properties such as tensile strength, ductility, and surface defects. The weight/diameter conversion formulas are given. Wires shall be furnished in the following specified finishes: Finish 1, Finish 2, Finish 3, Finish 4, Finish 5, Finish 6, and Finish 7. The material shall be smooth, free of twists, bends, kinks, curls, and as free of dents, swaging marks, scratches, die marks, laps, seams, splits, slivers, inclusions, bumps, pits, grooves, cracks, and other physical defects Unless black finish is specified, all types of wire shall have a clean finish, free of graphite, grease, oil, and lubricants. Wire for hooks, supports, springs, anchors, and mesh shall have a bright smooth surface free of cracks holes, or craters. The requirements for straightness, and coiling and spooling are detailed as well. The following analysis and tests shall be performed: chemical analysis, tensile test, ductility test, visual inspection, dimensional measurements, and examination for surface flaws.1.1 This specification covers three types of drawn wire suitable for fabrication into parts for electron tubes, lamps, and other devices; and one type of rod for metal-to-glass sealing (grid wire is excepted):1.1.1 Type 1A—Commercially pure nonsag wire (Note 2 and Note 3).1.1.2 Type 1B—Commercially pure rod suitable for metal-to-glass sealing.1.1.3 Type 2A—Thoriated filament wire containing 1 % thoria.1.1.4 Type 2B—Thoriated filament wire containing 2 % thoria.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 Types 1A and 1B are designated as UNS R07005. Type 2A is designated as UNS R07911. Type 2B is designated as UNS R07912.1.4 The following precautionary caveat pertains only to the Chemical Analysis, Section 12 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: A dimensional measurement method for testing nonsag tungsten wire above 0.030 in. (0.76 mm) in diameter is provided in Test Method F269.NOTE 2: Acceptance of nonsag wire characteristics for particular applications of size shall be by agreement between producer and consumer based on either a flashed microstructure as shown by photomicrographs, or on dimensional measurement limits determined in accordance with Test Method F269.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

9.1 Proprietary methods for manufacture of these materials vary significantly among suppliers, and these methods influence such properties as arc erosion, contact resistance, and tendency to weld in service. Since the performance of contacts in a device depends on numerous factors outside the contact itself (opening speed, closing speed, contact pressure, contact bounce, environmental variations, assembly technique and variations, etc.) this specification cannot ensure performance control in the application. As part of the qualification on initial samples it is recommended that the user functionally electrically test the materials for all devices applicable to the material's use. This specification will provide a means for the contact manufacturer and contact user to reach agreement on the details of material to be supplied for a specific use and reasonable assurance that future lots will be similar in properties and microstructure to the initial test or sample contacts supplied.AbstractThis specification covers electrical contact components made from silver-tungsten by powder-metallurgical procedures. The material shall conform to composition limits specified. The material shall be finished by braze alloy backing, tumbling to polish surfaces, special surface finish, silver-rich surface layer, cleaning, etc. Chemical analysis and physical test shall be made to conform to the specified requirements.1.1 This specification covers electrical contact components made from silver-tungsten by powder-metallurgical procedures.1.2 This specification covers compositions within the silver-tungsten system normally specified by users of contacts.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Data Safety Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏

This specification covers standard requirements for chromium-tungsten-molybdenum-vanadium, with or without tantalum, alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. The steel shall be killed and shall conform to the fine austenitic grain size requirements. Heat and product analyses shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, vanadium, boron, tantalum, and tungsten. The material shall undergo tensile test and shall conform to the required tensile properties such as tensile strength, yield strength, and elongation.1.1 This specification covers chromium-tungsten-molybdenum-vanadium, with or without tantalum, alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.1.2 Plates are available under this specification in two grades having different alloy contents as follows:Grade NominalChromiumContent, % NominalTungstenContent, % NominalMolybdenumContent, % NominalVanadiumContent, % NominalTantalumContent, %315 3.00 1.50 0.75 0.25 315T 3.00 1.50 0.75 0.25 0.101.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.1.4 The specification is expressed in both inch-pound units and in SI units; however, unless the order specifies the applicable “M” specification designation (SI units), the plates are furnished to inch-pound units.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

定价: 0元 / 折扣价: 0

在线阅读 收 藏

This specification covers higher strength chromium-molybdenum-tungsten alloy steel forgings intended primarily for use in boilers and pressure vessels for elevated temperature service. Materials shall be manufactured by melting processes, except that the open hearth process shall not be used, and that the molten steel shall be vacuum degassed prior to or during teeming of the ingot. The alloy steels may then be given an intermediate heat treatment such as normalizing and tempering or a subcrititcal anneal prior to rough machining. Heat analysis shall be obtained from samples to ensure chemical composition requirements are met. The steel forgings shall also undergo tension and Charpy impact tests and shall conform to the following required mechanical properties: tensile strength, yield strength, elongation, reduction of area, lateral expansion, minimum average absorbed energy, and minimum single value. Nondestructive examination procedures, such as straight-beam and angle-beam ultrasonic examination, and magnetic particle examination, shall also be executed.1.1 This specification covers chromium-molybdenum-tungsten alloy steel forgings intended primarily for use in boilers and pressure vessels for elevated temperature service.1.1.1 Elevated temperatures are temperatures in the range where creep and stress rupture properties are important for the alloy steels in this specification.1.2 Supplementary requirements are provided both in this specification and in the General Requirements Specification A788/A788M for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the purchase order or contract.1.3 Unless the order specifies the applicable “M” specification designation, the forgings shall be supplied to the inch-pound units.1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

定价: 0元 / 折扣价: 0

在线阅读 收 藏

This specification covers chromium-molybdenum-tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. The plates shall be available in three grades, namely Grades 23, 911, and 122, having different alloy contents. The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical requirements. The steel shall be killed and the plates shall undergo heat treatment. In order to determine mechanical properties such as yield strength and elongation, the plates shall be subjected to tension and hardness tests.1.1 This specification covers Chromium-Molybdenum-Tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.1.2 Plates are available under this specification in grades having different alloy contents as follows:Grade NominalChromiumContent, % NominalMolybdenumContent, % NominalTungstenContent, %       23 2.25 0.20 1.60911 9.00 1.00 1.0092 9.00 0.45 1.75122 12.00 0.40 2.001.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements.1.4 The specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏

The apparent size and distribution of tungsten carbide grains in cemented carbides affects the material’wear resistance and fracture. For a given chemical composition, an increase in the average grain size will result in increased toughness and decreased wear resistance. This practice illustrates representative micro-structures for a wide range of tungsten carbide-cobalt grades. This is not intended to be used as a specification for carbide grades; producers and users may use the micrographs and the grain size chart as a guide in developing their own specifications.1.1 This practice for the visual comparison and classification of the apparent grain size and distribution of cemented tungsten carbides is limited to cemented tungsten carbides that contain approximately 6, 10, and 18 % cobalt.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价: 0元 / 折扣价: 0

在线阅读 收 藏

This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within the silver-tungsten carbide system. The material shall conform to composition limits. Chemical analysis shall be performed to deteremine material conformance to specified composition requirements. The contact components shall agree on qualification tests for determination of physical properties. The tests shall be performed on production parts wherever practical or applicable. The test shall be determined after consideration of the function of the part.1.1 This specification covers electrical contact components made from silver-tungsten carbide materials by powder metallurgical processes.1.2 This specification covers compositions within the silver-tungsten carbide system normally specified by users of contacts.NOTE 1: Table X1.1 and Table X1.2 in Appendix X1 provide a list of typical compositions used for various applications.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏

3.1 This sample preparation procedure may be used to prepare metallographic samples for Guide B657. It does not include all variations of sample preparation.1.1 This guide prescribes a method for preparing cemented carbides for metallographic examination.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏
40 条记录,每页 10 条,当前第 1 / 4 页 第一页 | 上一页 | 下一页 | 最末页  |     转到第   页