定价： 515元 加购物车

This specification covers methyl amyl acetate2 (95 % grade) for use in paint, varnish, and related products. The apparent specific gravity, color property, distillation range, non-volatile matter, odor property, water property, acidity, and ester value shall be tested to meet the requirements prescribed.1.1 This specification covers methyl amyl acetate2 (95 % grade) for use in paint, varnish, and related products.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 For specific hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification.1.4 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification covers the requirements and corresponding test methods for vapor-degreasing grade perchloroethylene. When tested, materials shall conform to the following physical properties: specific gravity; distillation range (initial boiling point and dry point); acidity as HCl; alkalinity as NaOH; water content; appearance; color in Pt-co units; halides content; nonvolatile residues content; acid acceptance; and copper corrosion behavior.1.1 This specification covers vapor-degreasing grade perchloroethylene.2NOTE 1: Guide D3844 and Practice D4276 provide additional important information on solvent properties.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

4.1 Nuclear grade graphite is a composite material made from petroleum or a coal-tar-based coke and a pitch binder. Manufacturing graphite is an iterative process of baking and pitch impregnation of a formed billet prior to final graphitization, which occurs at temperatures greater than 2500 °C. The impregnation and rebake step is repeated several times until the desired product density is obtained. Integral to this process is the use of isotropic cokes and a forming process (that is, isostatically molded, vibrationally molded, or extruded) that is intended to obtain an isotropic or near isotropic material. However, the source, size, and blend of the starting materials as well as the forming process of the green billet will impart unique material properties as well as variations within the final product. There will be density variations from the billet surface inward and different physical properties with and transverse to the grain direction. Material variations are expected within individual billets as well as billet-to-billet and lot-to-lot. Other manufacturing defects of interest include large pores, inclusions, and cracks. In addition to the material variation inherent to the manufacturing process, graphite will experience changes in volume, mechanical strength, and thermal properties while in service in a nuclear reactor along with the possibility of cracking due to stress and oxidation resulting from constituents in the gas coolant or oxygen ingress. Therefore, there is the recognized need to be able to nondestructively characterize a variety of material attributes such as uniformity, isotropy, and porosity distributions as a means to assure consistent stock material. This need also includes the ability to detect isolated defects such as cracks, large pores and inclusions, or distributed material damage such as material loss due to oxidation. The use of this guide is to acquire a basic understanding of the unique attributes of nuclear grade graphite and its application that either permits or hinders the use of conventional eddy current, ultrasonic, or X-ray inspection technologies.1.1 This guide provides general tutorial information regarding the application of conventional nondestructive evaluation technologies (NDE) to nuclear grade graphite. An introduction will be provided to the characteristics of graphite that defines the inspection technologies that can be applied and the limitations imposed by the microstructure. This guide does not provide specific techniques or acceptance criteria for end-user examinations but is intended to provide information that will assist in identifying and developing suitable approaches.1.2 The values stated in SI units are to be regarded as the standard.1.2.1 Exception—Alternative units provided in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

This specification deals with Grade 80 heat-treated alloy steel chain for applications such as slings, lifting assemblies, and load binding. The alloy steel chain shall be made to a fully-killed fine austenitic grain process. Alloy steel chain may be made by the electric welding or gas welding process. The material shall be heat treated which includes quenching and tempering. Material's composition shall conform to the chemical requirements for carbon, phosphorous, sulfur, nickel, chromium, and molybdenum. The material shall conform to the mechanical property requirements for breaking force and elongation and to the dimensional requirements for the appropriate size chain. All chain shall be tested to at least the proof load.1.1 This specification covers Grade 80 heat-treated alloy steel chain for such applications as slings, lifting assemblies, and load binding. For overhead lifting applications, only alloy chain should be used.1.2 The chain grade is based on the nominal stress in the link at the design breaking force strength. It is calculated by taking the minimum breaking force load and dividing by two times the nominal cross-sectional area of the link.1.3 The values stated in either SI units or in other units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.3.1 Metric Units—Grade = 1/10 of the minimum breaking force in kilonewtons divided by two times the nominal cross-sectional area in square millimeters. = (MBF)/(0.005)(π)(d)(d)1.3.2 English Units—Grade = 0.000689 of the minimum breaking force in pounds divided by two times the nominal cross-sectional area in square inches. = (0.000689)(MBF)/(0.5)(π)(d)(d)1.3.3 MBF = minimum breaking force (lb or kN); d = chain diameter (in. or mm).NOTE 1: The above formulas are for round diameter links only. If different cross sections are used, the actual cross section of the link would need to be calculated and used.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification covers Grade 100 heat-treated alloy steel chain for such applications as slings, lifting assemblies, and load binding. The alloy steel shall be fully killed and have an austenitic grain size of five or finer. The steel shall be made by the electric welding or gas welding process. After welding, alloy steel chain shall be heat treated before applying the proof test. Heat and product analysis shall be performed and shall meet the required chemical composition in carbon, phosphorus, and sulfur. All chain shall be tested to at least the proof load and breaking force test specimen shall consist of a length from the lot containing at least the number of links. All chain shall be in the quenched and tempered condition before the elongation is measured.1.1 This specification covers Grade 100 heat-treated alloy steel chain for such applications as slings, lifting assemblies, and load binding. For overhead lifting applications, only alloy chain should be used.NOTE 1: This specification does not cover alloy steel chain for pocket wheel applications.1.2 This specification is a performance standard for Grade 100 chain used between −20 °F and 400 °F [−29 °C and 205 °C]. The chain manufacturer should be contacted for use at temperatures outside this range.1.3 The chain grade is based on the nominal stress in the link at the design breaking force strength. It is calculated by taking the minimum breaking force load and dividing by two times the nominal cross-sectional area of the link.1.4 The values stated in either SI units or in other units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4.1 Metric Units—Grade = 1/10 of the minimum breaking force in kilonewtons divided by two times the nominal cross-sectional area in square millimeters. = (MBF)/(0.005)(π)(d)21.4.2 English Units—Grade = 0.000689 of the minimum breaking force in pounds divided by two times the nominal cross-sectional area in square inches. = (0.000689)(MBF)/(0.5)(π)(d)21.4.3 MBF = minimum breaking force (lb or kN); d = chain diameter (in. or mm).NOTE 2: The above formulas are for round diameter links only. If different cross sections are used, the actual cross section of the link would need to be calculated and used.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification applies to pellets of stabilized zirconium oxide used in nuclear reactors. The chemical composition requirements such as the stabilizing additive (calcium oxide or yttrium oxide), analytical chemistry methods, impurity concentration (including hafnium, boron, gadolinium, samarium, europium, dysprosium, cobalt, silicon, iron, calcium, magnesium, aluminum, titanium, thorium, fluorine, chlorine, bromine, iodine, and hydrogen), and moisture concentration are prescribed. The nuclear grade pellets shall conform to the specified physical requirements which includes the following: physical dimensions, density, mechanical properties and test methods such as compressive test and thermal cycling test, and visual appearance such as end chips, circumferential chips, cracks, and fissures. The requirements for cleanliness before and after sampling and packaging are given.1.1 This specification applies to pellets of stabilized zirconium oxide used in nuclear reactors.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification covers the properties and requirements for pellets of stabilized cubic hafnium oxide used in nuclear reactors. Hafnium oxide should consist of a stabilizing agent, the recommended of which is yttrium oxide, though others such as calcium oxide and magnesium oxide may also be used as agreed upon by the buyer and seller. The material shall meet specified values of the following requirements: physical dimensions; density; mechanical properties; phase stabilization; impurity concentration limits; moisture concentration limit; visual appearance; end and circumferential chips; cracks; and fissures and other defects.1.1 This specification applies to pellets of stabilized cubic hafnium oxide used in nuclear reactors.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 515元 加购物车

定价： 646元 加购物车

4.1 A major concern of metals producers, warehouses, and users is to establish and maintain the identity of metals from melting to their final application. This involves the use of standard quality assurance practices and procedures throughout the various stages of manufacturing and processing, at warehouses and materials receiving, and during fabrication and final installation of the product. These practices typically involve standard chemical analyses and physical tests to meet product acceptance standards, which are slow. Several pieces from a production run are usually destroyed or rendered unusable through mechanical and chemical testing, and the results are used to assess the entire lot using statistical methods. Statistical quality assurance methods are usually effective; however, mixed grades, off-chemistry, and nonstandard physical properties remain the primary causes for claims in the metals industry. A more comprehensive verification of product properties is necessary. Nondestructive means are available to supplement conventional metals grade verification techniques, and to monitor chemical and physical properties at selected production stages, in order to assist in maintaining the identities of metals and their consistency in mechanical properties.4.2 Nondestructive methods have the potential for monitoring grade during production on a continuous or statistical basis, for monitoring properties such as hardness and case depth, and for verifying the effectiveness of heat treatment, cold-working, and the like. They are quite often used in the field for solving problems involving off-grade and mixed-grade materials.4.3 The nondestructive methods covered in this guide provide both direct and indirect responses to the sample being evaluated. Spectrometric analysis instruments respond to the presence and percents of alloying constituents. The electromagnetic (eddy current) and thermoelectric methods, on the other hand, are among those that respond to properties in the sample that are affected by chemistry and processing, and they yield indirect information on composition and mechanical properties. In this guide, the spectrometric methods are classified as quantitative, whereas the methods that yield indirect readings are termed qualitative.4.4 This guide describes a variety of qualitative and quantitative methods. It summarizes the operating principles of each method, provides guidance on where and how each may be applied, gives (when applicable) the precision and bias that may be expected, and assists the investigator in selecting the best candidates for specific grade verification or sorting problems.4.5 For the purposes of this guide, the term “nondestructive” includes techniques that may require the removal of small amounts of metal during the examination, without affecting the serviceability of the product.4.6 The nondestructive methods covered in this guide provide quantitative and qualitative information on metals properties; they are listed as follows:4.6.1 Quantitative: 4.6.1.1 X-ray fluorescence spectrometry, and4.6.1.2 Optical emission spectrometry.4.6.2 Qualitative: 4.6.2.1 Electromagnetic (eddy current),4.6.2.2 Conductivity/resistivity,4.6.2.3 Thermoelectric,4.6.2.4 Chemical spot tests,4.6.2.5 Triboelectric, and4.6.2.6 Spark testing (special case).1.1 This guide is intended for tutorial purposes only. It describes the general requirements, methods, and procedures for the nondestructive identification and sorting of metals.1.2 It provides guidelines for the selection and use of methods suited to the requirements of particular metals sorting or identification problems.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 10.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

定价： 515元 加购物车

定价： 515元 加购物车

定价： 515元 加购物车