微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读
AS 1952-2009/Amdt 1-2012 Dispensing measures - Pharmaceutical - Glass 被代替 发布日期 :  2012-12-24 实施日期 : 

定价: 0元 / 折扣价: 0

在线阅读 收 藏
AS 1952-2009 Dispensing measures - Pharmaceutical - Glass 被代替 发布日期 :  2009-05-19 实施日期 : 

定价: 689元 / 折扣价: 586

在线阅读 收 藏
AS 1952-1986 Dispensing measures - Pharmaceutical - Glass 现行 发布日期 :  1986-09-05 实施日期 : 

定价: 481元 / 折扣价: 409 加购物车

在线阅读 收 藏

5.1 Post dispensing volumetric expansion factor F indicates the ratio of the fully cured foam sealant volume and the initially dispensed foam sealant volume. For example, if the expansion factor F were 2, the fully cured foam would double its initial volume; therefore, one should fill 50 % of the cavity uniformly to anticipate the full coverage upon curing.5.2 Post dispensing volumetric expansion factor F does not predict the performance capability of the foam sealants of the suitability for the intended applications.5.3 This test method is intended to lend guidance in product selection as related to the post dispensing expansion characteristics of the aerosol foam sealants.5.4 This test method recognizes that the results are reflective of controlled laboratory conditions. Post dispensing expansion in field applications may vary according to temperature, humidity, and surfaces that the aerosol foam sealants are in contact with.1.1 This test method measures the volumetric expansion of aerosol foam sealants after dispensing.1.2 This test method provides a means for estimating the quantity of initial material required to dispense in order to fill a cavity.1.3 Aerosol foam sealants are used for a variety of applications intended to reduce airflow through the building envelope.1.4 This test method applies to two types of single component aerosol foam sealants: polyurethane and latex.1.5 There are no other known standard test methods to measure aerosol foam sealants post dispensing expansion.1.6 Values are reported in SI units only. Certain apparatus and supply items are referenced in inch-pound units for purchasing purposes.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏
B346-M1980 (R2002) Power-Operated Dispensing Devices for Flammable Liquids 现行 发布日期 :  1970-01-01 实施日期 : 

This PDF includes GI #2. 1. Scope 1.1 This Standard applies to the mechanical features of new and remanufactured power-operated dispensing devices for petroleum- base liquids for use as fuel in internal combustion engines where such devices are int

定价: 455元 / 折扣价: 387

在线阅读 收 藏
ANSI/IAS NGV4.1-1999/CSA 12.5-M99R04 NGV Dispensing Systems 现行 发布日期 :  1970-01-01 实施日期 : 

1.1 Scope 1.1.1 This standard applies to: (a) The mechanical and electrical features of newly manufactured systems that dispense natural gas for vehicles (NGV) where such a system is intended primarily to dispense the fuel directly into the fuel s

定价: 637元 / 折扣价: 542

在线阅读 收 藏