定价： 345元 / 折扣价： 294 元

定价： 481元 / 折扣价： 409 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

This specification is intended to provide a callout system for polyethylene utilizing specimen preparation procedures and test methods based primarily on ISO standards. The classification system provides for the identification of unfilled polyethylene plastics molding and extrusion materials, with a melt index of <1g/10 min, in such a manner that the supplier and the user agree on the acceptability of different commercial lots or shipments. The specification also lists the requirements that would allow for the use of recycled polyethylene materials. These requirements include the colour and form of the material.1.1 This classification system provides for the identification of unfilled polyethylene plastics molding and extrusion materials, with a melt index of <1g/10 min, in such a manner that the supplier and the user agree on the acceptability of different commercial lots or shipments. The tests involved in this specification are intended to provide information for identifying materials in accordance with the groups, classes, and grades covered. It is not the function of this classification system to provide specific engineering data for design purposes.1.2 This classification system allows for the use of recycled polyethylene materials provided that the requirements as stated in this classification system are met. The proportions of recycled material used, as well as the nature and amount of any contaminant, however, will not be covered in this specification.NOTE 1: See Guide D7209 for information and definitions related to recycled plastics.1.3 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These shall be agreed upon between the user and the supplier by using the suffixes given in Section 5.1.4 This classification system and subsequent line callout (specifications) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance requirements of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.1.5 The values stated in SI units are regarded as the standard.1.6 The following precautionary caveat pertains to the test method portion only, Section 12 of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.7 For information regarding plastic pipe materials, see Specification D3350. For information regarding wire and cable materials, see Specification D1248. For information regarding classification of PE molding and extrusion materials using ASTM test methods, see Specification D4976.NOTE 2: There is no known ISO equivalent to this standard.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elastomer compounds produced with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber, and so forth), colorants, stabilizers, lubricants, fillers, or reinforcements. Unreinforced polypropylene materials are classified into groups in accordance with basic composition. These groups are subdivided into classes and grades. The plastic composition shall be uniform and shall conform to the requirements specified. Tests shall be performed to determine the properties of the material in accordance with the following test methods: flow rate; tensile strength; flexural modulus; Charpy impact resistance; falling mass impact resistance; temperature of deflection under load; and multiaxial impact ductile-brittle transition temperature.1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elastomer compounds produced with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber, and so forth), colorants, stabilizers, lubricants, fillers, or reinforcements.1.2 This specification allows for the use of those polypropylene materials that can be recycled, reconstituted, and reground, provided that the following conditions are met:1.2.1 The requirements as stated in this specification and other ISO guidelines pertaining to these types of materials are met, and1.2.2 The material has not been modified in any way to alter its conformance to food contact regulations or similar requirements.1.3 The proportions of recycled, reconstituted, and regrind material used, as well as the nature and the amount of any contaminant, cannot be practically covered in this specification. It is the responsibility of the supplier and buyer of recycled, reconstituted, and regrind materials to ensure compliance.1.4 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications can be specified by using the suffixes as given in Section 5 and those in Classification System D4000.1.5 This classification system and specification are intended to provide a means of calling out polypropylene materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this specification.1.6 The values stated in SI units are to be regarded as the standard.1.7 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This specification is similar to both ISO 1873-1 and ISO 1873-2, but to different degrees. This specification resembles ISO 1873-1 in title only. The content is significantly different. This specification and ISO 1873-2 differ in approach or detail; data obtained using either are technically equivalent.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This classification system covers unfilled, reinforced filled, and impact modified materials suitable for injection molding, extrusion and blow molding using ISO methods. The system allows for the use of poly (phenylene sulfide) (PPS) plastic materials that are recycled, reconstituted recycled-regrind, recovered or reprocessed, or both, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered or reprocessed, or both, poly (phenylene sulfide) plastic materials to ensure compliance (see Guide D7209).1.2 The properties included in this classification are those required to identify the compositions covered. It is possible that other requirements are necessary to identify particular characteristics important to specialized applications. The use of suffixes as shown in Section 5 is one way of specifying these requirements.1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection needs to be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification.1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This standard and ISO 28078 address the same subject matter, but differ in technical content.NOTE 2: ASTM D4067 for PPS uses ASTM test methods.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

6.1 Means for selecting and identifying nonrigid vinyl chloride compounds are provided in Table 1. The properties enumerated in this table and the tests defined are expected to provide identification of the compounds selected. They are not necessarily suitable for direct application in design because of differences in shape of part, size, loading, environmental conditions, etc. Only when specimens are molded in accordance with 11.1.1 can comparative data be expected. The tests selected can also be used for inspection or quality control provided that they are performed strictly in accordance with the instructions given herein and in the designated methods so that extraneous variables are minimized and results are reproduced within the limits of variability of the material being examined and of the tests used for its examination.AbstractThis specification covers nonrigid vinyl chloride polymer and copolymer classes in which the resin portion of the composition contains at least 90 % vinyl chloride. The remaining 10 % may include one or more monomers copolymerized with vinyl chloride or consist of other resins mechanically blended with polyvinyl chloride or copolymers thereof. The identification of vinyl chloride polymers shall be in accordance with the specified terminology. Material shall be of uniform composition and be so compounded as to meet the requirements designated for it. Nonrigid vinyl chloride plastics ordinarily are supplied in either diced or granulated form. Durometer hardness, specific gravity, tensile strength, volatile loss, brittleness temperature, burning rate, and volume resistance shall be tested to meet the requirements specified.1.1 This classification system standard covers nonrigid vinyl chloride polymer and copolymer classes in which the resin portion of the composition contains at least 90 % vinyl chloride. The remaining 10 % can include one or more monomers copolymerized with vinyl chloride or consist of other resins mechanically blended with polyvinyl chloride or copolymers thereof.1.2 These nonrigid vinyl compounds are defined by a hardness range and include the necessary stabilizers, plasticizers, fillers, dyes, and pigments to meet the designated requirements.1.3 This classification system standard includes nonrigid vinyl chloride compounds recommended for compression molding, injection molding, and extrusion, but it must be recognized that particular compounds are not suitable for all these means of fabrication.NOTE 1: This standard and ISO 2898-1 and ISO 2898-2 address the same subject matter, but differ in technical content.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 The text of this classification system standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.1.7 Some applications have the option to contain recycled PVC plastics that meet the requirements of this classification system standard. Refer to the specific requirements in the Materials and Manufacture section of the applicable product standard.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification, which covers polystyrene materials, both crystal and rubber modified suitable for molding and extrusion, is intended to be a means of calling out plastic materials used in the fabrication of end items or parts. Polystyrene materials are classified according to classes after being grouped as crystal, rubber modified, and others. The materials are further classified according to grades after being grouped as general-purpose, other medium impact, high impact, super-high-impact, and others. The materials shall conform to the prescribed injection molded properties and natural colors.1.1 This classification system covers polystyrene materials, both crystal and rubber modified, suitable for molding and extrusion.1.2 This classification system and subsequent line callout (specification) are intended to be a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material other than those covered by this specification, and the economics.1.3 The properties included in this specification are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified using the suffixes as given in Section 5.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.NOTE 1: This standard combines elements from ISO 1622-1-2 and ISO 2897-1-2, but is not equivalent to either ISO standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification addresses the physical properties of copolymers of chlorotrifluoroethylene, perfluoroalkoxy, and tetrafluoroethylene that are suitable for extrusion, compression, and injection molding. It does not cover blended and recycled materials. Covered here is one type of fluoropolymer that is supplied in pellet form and classified according to their melting points, while the resins of each type are divided into four grades according to their melt flow rates. The materials shall be sampled in accordance with an adequate statistical sampling procedure and shall conform to specific gravity, melting point, flow rate, elongation, and tensile strength requirements when tested by the procedures itemized herein.1.1 This specification covers copolymers of chlorotrifluoroethylene, perfluoroalkoxy, and tetrafluoroethylene and are suitable for extrusion, compression, and injection molding.1.2 This specification does not cover blended materials and does not cover recycled materials.1.3 The values stated in SI units as detailed in IEEE/ASTM SI-10 are to be regarded as the standard. The values given in parentheses are for information only.1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: Although this classification system and ISO 20568-1 and ISO 20568-2 differ in approach or detail, data obtained using either are technically equivalent.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification addresses the physical properties of melt processible molding and extrusion materials of EFEP-fluoropolymer, wherein the EFEP resin is a copolymer of ethylene, tetrafluoroethylene, and hexafluoropropylene. It does not cover blended and recycled materials. Covered here are two types of fluoropolymer that is supplied in pellet form and classified according to their melting points, while the resins of each type are divided into one to two grades in accordance with their melt flow rates. The materials shall be sampled in accordance with an adequate statistical sampling procedure and shall conform to specific gravity, melting point, melt flow rate, elongation, tensile strength, and dielectric constant and dissipation factor requirements when tested by the procedures itemized herein.1.1 This specification covers melt processible molding and extrusion materials of EFEP-fluoropolymer. The EFEP resin is a copolymer of ethylene, tetrafluoroethylene, and hexafluoropropylene.1.2 This specification does not cover blended materials and does not cover recycled materials.1.3 The values stated in SI units as detailed in IEEE/ASTM SI-10 are to be regarded as the standard. The values given in parentheses are for information only.1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: Although this specification and ISO 20568-1 and ISO 20568-2 differ in approach or detail, data obtained using either are technically equivalent.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This classification system covers requirements for plasticized cellulose acetate propionate thermoplastic compounds suitable for injection molding and extrusion. These compounds have a propionyl content less than 48 % and an acetyl content less than 3 % and can contain dyes and pigments. Cellulosic plastic materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those cellulosic materials, provided that all specific requirements of this classification system are met.1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are specified by using the suffixes as given in Section 5.1.3 This classification system and subsequent line call out specification are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and performance required of the part, environment to which it will be exposed, fabrication process to be employed, costs involved, and inherent properties of the material other than those covered by this classification system.1.4 The values stated in SI units are to be regarded as standard.1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This classification system covers poly(ether ether ketone) materials suitable for injection molding and extrusion. This classification system allows for the use of recycled materials provided that all specification requirements are met.1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes in Section 5.1.3 This classification system and subsequent line callout (specification) are intended to provide means of calling out poly(ether ether ketone) materials used in the fabrication of end items or parts. It is not intended for the selection of materials. It is recommended that material selection be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the cost involved, and the inherent properties of the material other than those covered by this specification.1.4 Poly(ether ether ketone), commonly referred to as PEEK, is a member of the poly (aryl ether ketone) or PAEK family. Specification D6262 covers properties of PAEK shapes and includes shapes produced from PEEK.NOTE 1: This standard and ISO 23153 address the same subject matter, but differ in technical content.1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification provides for the identification of virgin, unmodified homopolymer ultra-high-molecular-weight polyethylene (UHMW-PE) molding and extrusion plastic materials in the form of powder, granules, or pellets. This specification is not intended to differentiate between various molecular weight grades of commercially available UHMW-PE, nor does it function to provide specific engineering data for design purposes. Sampled specimens shall be tested for dilute solution viscosity.1.1 This specification provides for the identification of virgin, natural color, unmodified homopolymer ultra-high-molecular-weight polyethylene (UHMWPE) plastics molding and extrusion materials. This identification is made in such a manner that the seller and purchaser can agree on the acceptability of different commercial lots or shipments.1.2 This specification also provides guidance for the characterization of UHMWPE materials based on various mechanical, thermal, electrical, and other analyses.1.3 It is not intended to differentiate between various molecular weight grades of ultra-high-molecular-weight polyethylene commercially available.1.4 It is not the function of this specification to provide specific engineering data for design purposes.1.5 Ultra-high-molecular-weight polyethylenes, as defined in this specification, are those linear polymers of ethylene which have a relative viscosity of 1.44 or greater, in accordance with the test procedures described herein.1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.7 The following precautionary caveat pertains only to the test method portions in Section 7 and the Annex and Appendixes, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This standard and ISO 11542-1 address the same subject matter, but differ in technical content. ISO 11542-1 provides a classification system based on various characteristics and a range of viscosity numbers determined in accordance with ISO 1628-3.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification is intended to provide a callout system for thermoplastic polyester (TPES) injection and extrusion materials, both virgin and recycled, based on ISO test methods. However, the proportions of recycled material used, and the nature and amount of any contaminant, as well as the selection of materials cannot be covered practically in this specification. Materials are classified into groups according to their composition, and are further subdivided into classes and grades as specified. Individual groups shall be identified in accordance to performance properties as to tensile strength, tensile modulus, Charpy impact strength, deflection temperature, melt flow rate, and density.1.1 This classification system covers thermoplastic polyester materials suitable for molding or extrusion.1.2 This classification system allows for the use of recycled thermoplastic polyester materials provided that the requirements as stated in this classification system and subsequent line callout (specification) are met. The proportions of recycled material used, as well as the nature and amount of any contaminant, however, cannot be covered practically in this specification.1.3 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5.1.4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and performance required of the part, the environment to which it will be exposed, the fabrication process to be used, the costs involved, and the inherent properties of the material other than those covered by this specification.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 The following hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This standard and ISO 7792-1:2012 and ISO 7792-2:2012 address the same subject matter, but differ in technical content.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This classification system covers liquid crystal polymeric (LCP) materials suitable for injection molding and extrusion. This classification system allows the use of liquid crystal polymers that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or a combination thereof, provided that the requirements as stated in this classification system are met. It is the responsibility of the supplier and the buyer of liquid crystal polymers that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or a combination thereof, to ensure compliance.1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are allowed. These shall be agreed upon between the user and the supplier, by using suffixes as given in Section 5.1.3 This classification system and subsequent line callout (specification) are intended to be a means of calling out plastic materials used in the fabrication of end-use items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.1.4 The values stated in SI units are to be regarded as standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车