定价： 1099元 / 折扣价： 935 元

定价： 1099元 / 折扣价： 935 元

定价： 1703元 / 折扣价： 1448 元

3.1 It is recognized that when comparing different types of rubber materials, the service performance may not correlate to the results of this predictive test.3.2 This test method should not be used as a measure of abrasion resistance for compositions that differ markedly from the standard reference compound. Misleading results, for example, are obtained from polyurethane compositions when compared with the standard reference compound.3.3 Some specimens may bounce (chatter) against the abrasive paper, producing inaccurate results. These should be interpreted with care and the condition reported.3.4 If test results are inconsistent, the specimens should be cut, after the test is run, and inspected for voids. If any voids are present, the results should be disregarded and the test repeated using test specimens that are free from voids.1.1 This test method covers the determination of the resistance to abrasion of vulcanized rubber, or other rubber materials that are similar to the standard reference compound, used for the soles and heels of footwear. It is not recommended for materials less than 2.5 mm (0.1 in.) in thickness.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 819元 / 折扣价： 697 元

3.1 Improperly fitted footwear can cause discomfort, but more importantly, prolonged use causes disfiguration of the bone structure, bunions, corns, callouses, and finally fatigue, often leading to serious accidents. Footwear performance may also be diminished if improperly fitted.1.1 This practice covers a practical method for fitting athletic footwear. This practice is applicable to the following general flexible types of footwear: running baseball, basketball, football, and tennis.1.2 There are as many variations in shoe forms and materials available to users as there are variations in the anatomy of the user's feet. Shoe forms are different due to manufacturer's materials, type of construction, and also the type of activity anticipated in its end use.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Since the heel is an integral support element of the shoe, the heel-attaching strength is a significant factor in ensuring the wearer's safety, as well as the longevity and serviceability of the shoe.4.2 This test should be performed on each new style shoe and when any changes are made in the design, material or method of shank or heel area of the shoe, or both, or in the attachment of the heel in an existing shoe.1.1 This test method covers the determination of the force required to detach the heel from footwear through the application of longitudinal tensile force at a constant displacement rate. The longitudinal test force simulates the most common heel failure mode. Heel height of 20 mm (13/16 in.) or larger is needed to perform this test method properly. Most women's medium and high heeled footwear meets this requirement.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 The terminology standard covers terminology related to walkway safety and footwear.1.2 Words adequately defined in standard dictionaries are not included. Included are words that are particular to this industry and those contained in standards under the jurisdiction of ASTM Committee F13 on Pedestrian/Walkway Safety and Footwear.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers minimum slip resistance requirements for the performance of protective (safety) footwear and is intended to help reduce potential injuries. Controlled laboratory tests used to determine compliance with this performance specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed to.1.2 The cited Test Method F2913 allows for testing of alternative flooring or contaminates, or both. It is suggested that testing those alternatives be considered should specific workplace hazards exist.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification provides certification of protective footwear. It includes performance requirements for footwear to protect workers' feet from a variety of workplace hazards.1.1 The principal purpose of this specification is the certification of protective footwear. Certification must be performed by independent third party laboratories in order for footwear to bear the ASTM marking.1.2 The specification contains performance requirements for footwear to protect workers' feet from the following hazards by providing: (1) conductive properties (Cd) which reduce hazards that may result from static electricity buildup; and reduce the possibility of ignition of explosives and volatile chemicals; (2) electric hazard protection (EH), to protect the wearer from accidental contact by stepping on live electric wires; (3) static dissipative properties (SD) to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required; (4) puncture resistance (PR) footwear devices.1.3 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards other than the toe area that can potentially result in injury.1.4 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.1.5 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.1.6 Any changes to the original components of safety footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this specification rendering the ASTM Soft Toe Protective Footwear label invalid.1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This non-proprietary laboratory test method allows for the reproducible testing of whole footwear and footwear-related soling materials for evaluating relative slip performance. Other ASTM test methods generally employ a standardized test foot primarily for evaluation of flooring materials.1.1 This test method2 determines the dynamic coefficient of friction between footwear and floorings under reproducible laboratory conditions for evaluating relative slip performance. The method is applicable to all types of footwear, outsole units, heel top lifts and sheet soling materials, also to most types of floorings, including matting and stair nosing, and surface contaminants on the flooring surface, including but not limited to liquid water, ice, oil and grease. The method may also be applied to surfaces such as block pavers, turf and gravel.1.2 Special purpose footwear or fittings containing spikes, metal studs or similar may be tested on appropriate surfaces but the method does not fully take account of the risk of tripping due to footwear/ground interlock.1.3 The values stated in the ASTM test method in metrics are to be regarded as the standard. The values in parentheses are for information.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 Electrical contact injuries to workers may involve a current path through the feet of the worker. The footwear covered by this specification is dielectrically rated to provide additional insulation and isolation to the wearer. This test method will determine that dielectric footwear has dielectric integrity at the time of the test.1.1 This test method covers testing to determine the “Dielectric Strength” of dielectric overfoot and overshoe footwear. Testing is done over the maximum possible area of the dielectric footwear without permitting flashover between electrodes.1.2 The use and maintenance of dielectric footwear is beyond the scope of this test method.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in 5.2.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers acceptance testing of dielectric overfoot and overshoe footwear designed to provide additional isolation or insulation of workers if in accidental contact with energized electrical conductors, apparatus, or circuits. Styles of overshoe footwear covered under this specification shall be designated as: Rubbers, designed to be worn over existing footwear and to cover only the foot of the worker; Boots, designed to be worn over existing footwear and to cover the foot and lower leg of the worker to below the knee; and Galoshes, designed to be worn over existing footwear and to cover the foot and lower leg of the worker to below the knee and having fasteners to close the folded front flaps. Each article of overshoe footwear shall be given a proof test and shall withstand the 60-Hz ac proof-test voltage (rms value) or the dc proof-test voltage (average value).1.1 This specification covers acceptance testing of dielectric overfoot and overshoe footwear designed to provide additional isolation or insulation of workers if in accidental contact with energized electrical conductors, apparatus, or circuits.1.2 Three styles of overshoe footwear are provided and are designated as rubbers, boots, and galoshes.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This practice establishes the standard procedures for ranking the measured slip resistance data of footwear sole, heel, and other related materials on various walkway surfaces.1.1 This practice covers the ranking of slip resistance of footwear sole, heel, or related materials on various walkway surfaces.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

When the conditions are such that foreign materials can come between shoe bottoms and a walkway surface, efforts should be made to design the walkway surface to remove the foreign material from between shoe bottoms and the walkway surface.This type of slip hazard is often found in manufacturing and maintenance processes where foreign materials are frequently present on walkway surfaces. Examples are: food preparation and processing areas, rendering operations, transportation and cargo handling activities.1.1 This guide is intended to assist in the selection of walkway surfaces where the presence of foreign materials may produce the danger of a slip or a fall.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元