This specification covers hot-wrought, special quality microalloyed carbon steel bars intended for use as hot forging stock. The bars shall be hot-wrought, as-wrought, unless thermal treatment is necessary to ensure cold shearability. The steel specimens shall be killed and shall conform to the fine grain size requirement. Heat analysis and product analysis shall be performed wherein the specimens shall conform to the required chemical compositions of vanadium, columbium, and molybdenum.1.1 This specification covers hot-wrought, special quality microalloyed carbon steel bars intended for use as hot forging stock. The bars shall be hot-wrought, as-wrought, unless thermal treatment is necessary to ensure cold shearability.1.2 The bars shall be furnished to chemical composition only. Chemical composition is based on standard carbon steel grades modified to include microalloying elements such as columbium (niobium), vanadium, or molybdenum. Desired mechanical properties are developed in the subsequent hot forging and controlled cooling operations.1.3 Sections and sizes of bar steel available are covered in Specification A29/A29M.1.4 Supplementary Requirements S1 to S6 are provided for use when additional controls or requirements are desired. These shall apply only when specified on the purchase order.1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text and tables, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers stainless steel billets and bars for forging. The steel materials shall be annealed and conditioned by chipping or grinding. The steel specimens shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, nitrogen, and other elements.1.1 This specification covers stainless steel billets and bars intended only for forging.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers hot-finished or cold-finished precipitation hardening iron base superalloy bars, forgings, and forging stock for high-temperature service. The mechanical properties of these alloys are developed by suitable solution treating and precipitation hardening treatments. Two grades of iron base alloy are covered; Grade 660 and Grade 662 (bars and forgings). The material shall meet the requirements as to stress rupture properties specified. The material shall conform to the chemical, mechanical, and metallurgical properties requirements specified.1.1 This specification2 covers hot-finished or cold-finished precipitation hardening iron base superalloy bars, forgings, and forging stock for high-temperature service. The mechanical properties of these alloys are developed by suitable solution treating and precipitation hardening treatments.1.2 Two grades of iron base alloy are covered. Selection will depend upon design, service conditions, mechanical properties, and elevated temperature characteristics.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers UNS N05500 nickel-copper-aluminum alloy rounds, squares, hexagons, rectangles, and forgings and forging stocks manufactured by either hot working or cold working, and cold-worked wire. The material should conform to the required mechanical properties in both aged and unaged conditions. Precipitation hardening is accomplished by holding the material at a high temperature, followed by furnace cooling and then air cooling.1.1 This specification covers nickel-copper-aluminum alloy (UNS N05500) in the form of rounds, squares, hexagons, or rectangles, and forgings and forging stock, manufactured either by hot working or cold working, and cold-worked wire.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers hot- and cold-worked precipitation hardenable cobalt-containing alloys (UNS R30155 and UNS R30816) rod, bar, forgings, and forging stock for high temperature service. The material shall conform to the required chemical composition for carbon, manganese, silicon, phosphorus, sulfur, chromium, nickel, molybdenum, columbium, tantalum, iron, cobalt, and nitrogen. The materials shall conform to the required tensile and hardness properties such namely tensile strength, yield strength, alongation and Brinell hardness. The alloys shall also conform to the required stress-rupture properties. Dimensions such as diameter, thickness, or width, out-of-round, corners, cut lengths, straightness for cold-worked and hot-worked rod and bar shall be measured.1.1 This specification covers hot- and cold-worked precipitation hardenable cobalt-containing alloys (UNS R30155 and UNS R30816)2 rod, bar, forgings, and forging stock for high-temperature service.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers cast carbon and alloy steel ingots and strand castings, semi-wrought ingots and strand castings, and rolled or forged blooms, billets, and slabs for steel forging stock. Materials shall be manufactured and furnished in a condition that can withstand, for an indefinite time, exposure to all climatic conditions without developing any external or internal cracks. Final products shall be free of injurious surface imperfections. If, however, such defects do occur, surface conditioning, cutting, or parting may be performed by scarfing or flame-cutting. Heat and product analyses shall be carried out to evaluate conformance of steel specimens to chemical composition requirements.1.1 This specification covers cast carbon and alloy steel ingots and strand castings, semi-wrought ingots and strand castings and rolled or forged blooms, billets, and slabs for forging.1.2 Blooms, billets, and slabs are semi-finished steel products, hot rolled or forged to approximate cross-sectional dimensions. Blooms and billets may be square, round, octagonal, or rectangular in section; slabs are rectangular. Although no invariable rule prevails between the terms blooms and billets, and they are frequently used interchangeably, the following size distinctions are in general use.1.2.1 Blooms—Cross-sectional area greater than 36 in.2 [230 cm2].1.2.2 Billets—Maximum cross-sectional area 36 in.2 [230 cm2].1.2.3 Slabs—Minimum thickness, 11/2 in. [4 cm]; width, more than twice the thickness; and generally a cross-sectional area of not less than 16 in.2 [100 cm2].1.2.4 Ingots either top or bottom poured or secondary remelted are covered.1.2.5 Strand castings with or without additional reduction are covered.1.3 Supplementary Requirements (S1 to S19) of an optional nature are provided. They shall apply only when specified by the purchaser.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 Unless the order specifies the “M” specification, the material shall be furnished to the inch-pound units.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers martensitic chromium stainless steel forgings, forged bars, and forging stock for high-temperature service. The mechanical properties are developed by suitable heat treatment, as indicated for each alloy. Steel materials shall be manufactured by melting and forging processes, and heat treatments, that shall consist of austenizing, quenching, tempering, and stress relieving. Stainless steels may then be furnished in one of the following hot-finished conditions: as forged without descaling; forged and descaled; rough turned or rough machined. Specimens shall conform to required chemical compositions. Forgings shall undergo tension, impact, stress rapture, and hardness tests, and should conform to mechanical properties prescribed for individual grades and classes. These mechanical properties are: tensile strength, yield strength, elongation, reduction of area, impact strength, and Brinell and Rockwell hardness.1.1 This specification covers martensitic chromium stainless steel forgings, forged bar, and forging stock for high temperature service. The mechanical properties are developed by suitable heat treatment, as indicated for each alloy.1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification establishes the requirements for copper (UNS Nos. C11000, C14500, and C14700) and copper alloy (UNS Nos. C36500, C37000, C37700, C46400, C48200, C48500, C61900, C62300, C63000, C63200, C64200, C64210, C65500, C67500, C67600, C69300, C70620, C71520, and C77400) forging rods, bars, and shapes. The material for manufacture shall be a cast rod, bar, or billet of such purity and soundness as to be suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure in the finished product. Products shall be produced in tempers H50 (extruded and drawn), M20 (as hot rolled), and M30 (as hot extruded). Products shall be tested and shall adhere to dimensional (diameter, thickness, width, length, shape, and straightness), mechanical, and chemical composition requirements.1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved:Copper UNS Nos. Copper AlloyUNS Nos. Copper AlloyEN 1412 Nos.       C11000 C27450 C49350 CW612NC14500 C27451 C49355 CW617NC14700 C27453 C49360    C28500 C61900    C35330 C62300    C36300 C63000    C36500 C63200    C37000 C64200    C37700 C64210    C46400 C65500    C46500 C65680    C46750 C67500    C48200 C67600    C48500 C69150    C48600 C69240    C48640 C69300    C48645 C69410    C49250 C69850    C49255 C70620    C49260 C71520    C49265 C77400    C49300 C87700    C49340 C87710    C49345    NOTE 1: Additional information about forging practice and forgings produced from these alloys is given in Appendix X1 and in Specification B283/B283M.1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following copper and copper alloys are included: Copper or Previously Copper Alloy Used Des- UNS No. ignation Name C11000 12 Copper C14500 ... Copper-tellurium C14700 Copper-sulfur C36500 Leaded muntz metal, uninhibited C37700 2 Forging brass C46400 3 Naval brass C48200 ... Medium-leaded naval brass C48500 13 Leaded naval brass C61900 ... Aluminum bronze C62300 ... Aluminum bronze, 9% C63000 11b Aluminum-nickel bronze C63200 ... Aluminum-nickel bronze C64200 ... Aluminum-silicon bronze C64210 ... Aluminum-silicon bronze, 6.7% C65500 7 High-silicon bronze (A) C67500 4 Manganese bronze (A) C77400 14 Nickel silver, 45-10 1.2 The values stated in SI units are the standard. 1.3 This specification is the companion to inch-pound Specification B124.

定价： 0元 / 折扣价： 0 元

This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. The steel shall conform to the required chemical composition requirements. The material shall also conform to the requirements as to mechanical properties. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification.1.1 This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers carbon steel plates, intended for forging, quenching-and-tempering, and similar applications in which uniformity of composition and freedom from injurious imperfections are important. Heat analysis of steel shall conform to the chemical requirements for carbon, manganese, phosphorus, sulfur, and silicon.1.1 This specification covers carbon steel plates, forging quality, intended for forging, quenching-and-tempering, and similar applications in which uniformity of composition and freedom from injurious imperfections are important.1.2 The plates are available in six grades, or chemical compositions.1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1. Scope and Purpose 1.1 Scope This Standard covers the occupational health and safety requirements for all classes of power forging machinery, both for impression die and flat die forging, including power-driven and gravity-drop hammers; mechanica

定价： 410元 / 折扣价： 349 元

4.1 The extensive porosity present in pressed and sintered ferrous materials masks the effect of inclusions on mechanical properties. In contrast, the properties of material powder forged to near full density are strongly influenced by the composition, size, size distribution, and location of nonmetallic inclusions.4.2 The test for nonmetallic inclusions in powder forged steels is useful as the following:4.2.1 Characteristic to classify or differentiate one grade of powder from another.4.2.2 Means of quality comparison of powders intended for powder forging, lot to lot.4.3 Significant variations in nonmetallic inclusion content will occur if:4.3.1 The powder used to form the test specimen does not meet powder forging quality standards for nonmetallic inclusion content.4.3.2 Processing of the powder forged test specimen has been carried out under conditions that do not permit oxide reduction or allow oxidation of the test specimen, or both.1.1 This test method covers a metallographic method for determining the nonmetallic inclusion level of ferrous powders intended for powder forging (PF) applications.1.2 The test method covers repress powder forged test specimens in which there has been minimal lateral material flow (< 1 %). The core region of the powder forged test specimen shall contain no porosity detectable at 100×.1.3 This test method is not suitable for determining the nonmetallic inclusion level of powder forged test specimens that have been forged such that the core region contains porosity. At the magnification used for this test method, residual porosity is hard to distinguish from oxide inclusions. Too much residual porosity makes a meaningful assessment of the inclusion population impossible.1.4 The test method may be applied to materials that contain manganese sulfide (admixed or prealloyed), provided the near neighbor separation distance is changed from 30 μm to 15 μm.NOTE 1: The test method may be applied to powder forged parts where there has been a greater amount of material flow provided:The near neighbor separation distance is changed, orThe inclusion sizes agreed between the parties are adjusted for the amount of material flow.1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车