微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读

定价: 605元 / 折扣价: 515

在线阅读 收 藏

定价: 481元 / 折扣价: 409 加购物车

在线阅读 收 藏

定价: 481元 / 折扣价: 409 加购物车

在线阅读 收 藏

定价: 605元 / 折扣价: 515 加购物车

在线阅读 收 藏

定价: 481元 / 折扣价: 409 加购物车

在线阅读 收 藏

5.1 This standard practice establishes a method for conducting accelerated laboratory aging of radial passenger or light truck tires, or both, in an oven.5.2 The goal of this practice is to define a scientifically valid protocol for the accelerated laboratory aging of a tire such that certain of its material properties correlate to those of in-service tires (see Appendix X1). This practice does not establish performance limits or tolerances for tire specifications.1.1 This practice describes a method to laboratory age a new tire in an oven to produce changes in certain chemical and physical properties at the belt edges similar to those of tires in-service (see Appendix X1).1.2 This practice is a precursor to conducting an ASTM standard roadwheel test method for laboratory generation of belt separation in radial passenger car and light truck tires.1.3 This practice may not produce representative chemical and physical property changes in any part of the tire except the belt edge.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

4.1 Because of wide variations in service conditions, no correlation between these accelerated tests and service performance is given or implied. However, the test methods yield data that can be used to estimate relative service quality of different compounds. They are often applicable to research and development studies.1.1 These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 702元 / 折扣价: 597 加购物车

在线阅读 收 藏

4.1 The intended use of this guide is to provide practical assistance in the development of an optimized sampling design. This standard describes or discusses:4.1.1 Sampling design selection criteria,4.1.2 Factors impacting the choice of a sampling design,4.1.3 Selection of a sampling design,4.1.4 Techniques for optimizing candidate designs, and4.1.5 The criteria for evaluating an optimized sampling design.4.2 Within a formal USEPA data generation activity, the planning process or data quality objectives (DQOs) development is the first step. The second and third are the implementation of the sampling and analysis design and the data quality assessment. Within the DQO planning process, the selection and optimization of the sampling design is the last step, and therefore, the culmination of the DQO process. The preceding steps in the DQO planning process address:4.2.1 The problem that needs to be addressed,4.2.2 The possible decisions,4.2.3 The data input and associated activities,4.2.4 The boundaries of the study,4.2.5 The development of decision rules, and4.2.6 The specified the limits on decision error.4.3 This guide is not intended to address the aspects of the planning process for development of the project objectives. However, the project objectives must be outlined and communicated to the design team, prior to the selection and optimization of the sample design.4.4 This guide references statistical aspects of the planning and implementation process and includes an appendix for the statistical calculation of the optimum number of samples for a given sampling design.4.5 This guide is intended for those who are responsible for making decisions about environmental waste management activities.1.1 This document provides practical guidance on the selection and optimization of sample designs in waste management sampling activities, within the context of the requirements established by the data quality objectives or other planning process.1.2 This document (1) provides guidance for selection of sampling designs; (2) outlines techniques to optimize candidate designs; and (3) describes the variables that need to be balanced in choosing the final optimized design.1.3 The contents of this guide are arranged by section as follows:1.   2. Referenced Documents   3. Terminology   4.   5. Summary of Guide   6. Factors Affecting Sampling Design Selection    6.1 Sampling Design Performance Characteristics    6.2 Regulatory Considerations    6.3 Project Objectives    6.4 Knowledge of the Site    6.5 Physical Sample Issues    6.6 Communication with the Laboratory    6.7 Analytical Turn Around Time    6.8 Analytical Method Constraints    6.9 Health and Safety    6.10 Budget/Cost Considerations    6.11 Representativeness   7. Initial Design Selection  8. Optimization Criteria  9. Optimization Process    9.2 Practical Evaluation of Design Alternatives    9.3 Statistical and Cost Evaluation   10. Final Selection     Annex A1 Types of Sampling Designs    A1.1 Commonly Used Sampling Designs    A1.2 Sampling Design Tools    A1.3 Combination Sample Designs   Appendix X1. Additional References   Appendix X2. Choosing Analytical Method Based on Variance and Cost   Appendix X3. Calculating the Number of Samples: A Statistical Treatment  1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 843元 / 折扣价: 717 加购物车

在线阅读 收 藏
25 条记录,每页 10 条,当前第 1 / 3 页 第一页 | 上一页 | 下一页 | 最末页  |     转到第   页