定价： 481元 / 折扣价： 409 元

定价： 481元 / 折扣价： 409 元

5.1 This procedure describes a rapid and sensitive method for estimating the stability reserve of an oil. The stability reserve is estimated in terms of a separability number, where a low value of the separability number indicates that there is a stability reserve within the oil. When the separability number is between 0 to 5, the oil can be considered to have a high stability reserve and asphaltenes are not likely to flocculate. If the separability number is between 5 to 10, the stability reserve in the oil will be much lower. However, asphaltenes are, in this case, not likely to flocculate as long as the oil is not exposed to any worse conditions, such as storing, aging, and heating. If the separability number is above 10, the stability reserve of the oil is very low and asphaltenes will easily flocculate, or have already started to flocculate.5.2 This test method can be used by refiners and users of heavy oils, for which this test method is applicable, to estimate the stability reserves of their oils. Hence, this test method can be used by refineries to control and optimize their refinery processes. Consumers of oils can use this test method to estimate the stability reserve of their oils before, during, and after storage.5.3 This test method is not intended for predicting whether oils are compatible before mixing, but can be used for determining the separability number of already blended oils. However, experience shows that oils exhibiting a low separability number are more likely to be compatible with other oils than are oils with high separability numbers.1.1 This test method covers the quantitative measurement, either in the laboratory or in the field, of how easily asphaltene-containing heavy fuel oils diluted in toluene phase separate upon addition of heptane. The result is a separability number (%). See also Test Method D7061.1.2 The test method is limited to asphaltene-containing heavy fuel oils. ASTM specification fuels that generally fall within the scope of this test method are Specification D396, Grade Nos. 4, 5, and 6, Specification D975, Grade No. 4-D, and Specification D2880, Grade Nos. 3-GT and 4-GT. Refinery fractions from which such blended fuels are made also fall within the scope of this test method.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 702元 / 折扣价： 597 元 加购物车

5.1 This test method assesses the performance of an engine oil with respect to control of piston deposits and maintenance of oil consumption under heavy-duty operating conditions selected to accelerate deposit formation in a turbocharged, intercooled four-stroke-cycle diesel engine equipped with a combustion system that minimizes federally controlled exhaust gas emissions.5.2 The results from this test method may be compared against specification requirements to ascertain acceptance.5.3 The design of the test engine used in this test method is representative of many, but not all, diesel engines. This factor, along with the accelerated operating conditions, needs to be considered when comparing test results against specification requirements.1.1 The test method covers a heavy-duty engine test procedure under high output conditions to evaluate engine oil performance with regard to piston deposit formation, piston ring sticking and oil consumption control in a combustion environment designed to minimize exhaust emissions. This test method is commonly referred to as the Caterpillar C13 Heavy-Duty Engine Oil Test.31.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.2.1 Exceptions—Where there are no SI equivalent such as screw threads, National Pipe Treads (NPT), and tubing sizes.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 843元 / 折扣价： 717 元 加购物车

1.1 This specification covers hot-rolled heavy-thickness carbon-steel sheet and strip of structural quality in coils beyond the size limits of Specification A570/A570M. This material is intended for structural purposes where mechanical test values are required and is available in the sizes listed below. This material is available only in coils as described below: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip over 8 to 12 0.230 to 0.750, incl (200 to 300) (6.0 to 19) Sheet over 12 to 48 0.230 to 0.750, incl (300 to 1200) (6.0 to 19) over 48 (1200) 0.180 to 0.750, incl (4.5 to 19) 1.1.1 The following grades are covered in this specification: Mechanical Properties Yield Point min, Tensile Strength Grade ksi (MPa) min, ksi (MPa) 30 30 (205) 49 (340) 33 33 (230) 52 (360) 36 36 (250) 53 (365) 40 40 (275) 55 (380) 1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values of the two systems may result in nonconformance with this specification. 1.3 Sheet and strip in coils of the sizes noted in 1.1 can be included in this specification only with the following provisions: 1.3.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils), 1.3.2 This specification is not applicable to the steels covered by Specification A635/A635M, 1.3.3 The dimensional tolerances from Specification A635/A635M are applicable to material produced in accordance with this specification, 1.3.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming, and 1.3.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.

定价： 0元 / 折扣价： 0 元

3.1 Prior to beginning a project that involves the removal, cutting, grinding, or burning of paint, it is necessary to determine if the coating contains hazardous metals, such as lead. If it does, certain requirements for worker and environmental protection may need to be imposed. The presence and quantity of hazardous metals in a paint can be determined through laboratory analysis. Proper sampling protocol is needed to assure the laboratory results represent the actual amount of heavy metal in the coating. The number and location of samples to be removed must also be determined to characterize properly the extent of the presence of hazardous materials, if any, on a structure.1.1 This practice covers a method to control the removal of samples of coating films from substrates for subsequent laboratory analysis for heavy metal content on a mass basis. This technique can be used in the field, the fabricating shop, or laboratory.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 5, Note 1, and Note 3.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

A2.4 A2.4.1 This test method describes the testing procedure that shall be used to qualify material for use in ASTM F3111 bolts made of any steel composition permitted by this specification. The test method measures the susceptibility of the material to the influence of an externally applied potential (see A2.7.2.3.2) by testing for the threshold of embrittlement in a salt solution environment.1.1 This specification covers heat treated, alloy steel, heavy hex structural bolt/nut/washer assemblies, also referred to as “sets,” having a tensile strength of 200 to 215 ksi. These assemblies are capable of developing a minimum predetermined tension when installed by applying an initial torque followed by rotation to the nut or bolt head, while at the same time preventing the rotation of the opposite side of the assembly.NOTE 1: The installations in Appendix X1 are important to the proper application of this product.1.2 An assembly consists of a heavy hex structural head bolt, nut and two washers covered by this specification.1.3 The assemblies are available in sizes 1 in. to 1 1/4 in. inclusive.1.4 The fastener assemblies are intended for use in structural connections in the following environmental conditions:1.4.1 Interiors, normally dry, including interiors where structural steel is embedded in concrete, encased in masonry or protected by membrane or noncorrosive contact type fireproofing.1.4.2 Interiors and exteriors, normally dry, under roof, where the installed assemblies are soundly protected by a shop-applied or field-applied coating to the structural steel system.1.5 The fastener assemblies are not intended for use in structural connections in the following environments, with or without protection by a shop-applied or field-applied coating to the structural steel system:1.5.1 Exteriors not under roof.1.5.2 Chemical environments in which strong concentrations of highly corrosive gases, fumes, or chemicals, either in solution or as concentrated liquids or solids, contact the fasteners or their protective coating.1.5.3 Heavy industrial environments severe enough to be classified as a chemical environment as described in 1.5.2.1.5.4 Condensation and high humidity environments maintaining almost continuous condensation, including submerged in water and soil.1.5.5 Cathodically protected environments, in which current is applied to the structural steel system by the sacrificial anode method or the DC power method.1.6 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.7 The following precautionary statement pertains only to the test method portions, Section 13, Section 14 and Annex A2 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers malleable iron flanges, pipe fittings, and valve parts, including parts to be assembled for use in railroad, marine, and other heavy duty service applications. The sizes, shapes, and dimensions of the fittings shall conform to the requirements specified. The iron shall be produced under constant control of chemical composition and physical properties. Records of the chemical composition of the iron and of the physical properties of the test specimens shall be systematically made and maintained.1.1 This specification covers malleable iron flanges, pipe fittings, and valve parts, including parts to be assembled for use in railroad, marine, and other heavy-duty service applications where fittings furnished in accordance with American National Standard for Malleable Iron Threaded Fittings, Classes 150 and 300 (ANSI B16.3) are not considered adequate.1.2 Service shall include up to 650 °F (345 °C).21.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers heavy-duty ranges that use gas or electrical heat sources, or both, for cooking food in the commercial and institutional food service establishments. Types: type I-electric range top with electric oven; type I-electric range top with gas-fired oven; type I-electric range top with storage base; type II-gas-fired range top with gas-fired oven; type II-gas-fired range top with electric oven; and type II-gas-fired range top with storage base. Electric ovens: electric standard oven and electric convection oven. Power: natural gas, propane, manufactured gas, and other gases. All ranges shall be provided with means to regulate the oven interior temperature and cook top burner heat. Oven thermostat test shall be performed to meet the requirements prescribed.1.1 This specification covers heavy-duty ranges that use gas or electrical heat sources, or both, for cooking food in the commercial and institutional food service establishments.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 A non-aqueous engine coolant is a glycol, diol, triol, or mixtures thereof, based heat transfer fluid containing less than 1.0 % water when formulated and intended for final use without dilution with water. (Definition from Terminology D4725.)1.2 This specification covers the requirements for fully formulated non-aqueous glycol base coolants for cooling systems of heavy-duty engines. These coolants will function effectively during both winter and summer to provide protection against corrosion, cavitation, freezing, boiling, and excessive viscosity.1.3 This specification is intended to cover the requirements for non-aqueous engine coolants prepared from virgin glycols, diols, or triols, or mixtures thereof.1.4 Coolants meeting this specification exhibit very low vapor pressures under all operating conditions, thereby avoiding the creation and collapse of coolant vapor, the primary cause of pump and cylinder liner cavitation erosion. They may additionally contain additives that provide traditional anti-cavitation erosion coatings but there is no requirement that they must. Non-aqueous engine coolants usually contain one or more carboxylates and do not normally contain nitrites. It is suggested that coolant testing be undertaken at normal manufacturer’s recommended intervals to monitor degradation products. The low vapor pressures inherent in coolants that meet this specification also provide protection from hot surface scaling, as liquid coolant is in contact with all hot metal surfaces of the engine cooling system at all times.1.5 Water is a contaminant to non-aqueous engine coolants and it is suggested that water content be tested periodically with test strips to ideally keep water content of the coolant at 3 % or less. Increases in water cause an undesirable drop in the boiling point. It is instructive that the glassware corrosion testing per this specification is conducted at 6 % corrosive water.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

This specification covers the general requirements for hot-rolled, heavy-thickness, and high-strength low-alloy with improved formability sheet and strip coils. These coils are normally produced from rimmed, capped, or semi-killed steel. Steels may be produced as ingot-cast or strand-cast. Cast or heat analysis shall be made to determine the conformance with the requirements. For steels other than non-killed (capped or rimmed), product analysis may be made. The chemical analysis shall conform to the specified amounts of carbon, manganese, phosphorus, sulfur, silicon, and copper. Steels may or may not be subjected to tension test requirement. Specimen preparation and test methods are discussed. The mechanical property requirements, number of specimens, test locations, and specimen orientation shall be in accordance with the applicable product specification. Tolerances for the dimensions of sheet and strip coils are specified.1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.1.2 It applies to Specifications A414/A414M, A424/A424M, A1018/A1018M, and A1031/A1031M.1.3 This material is available only in coils described as follows:  Size Limits, Coils Only     Product Width, in. [mm] Thickness, in. [mm]     Strip over 8 to 12, incl[over 200 through 300] 0.230 to 1.000, incl[from 6.0 through 25]Sheet All WidthsAAll Widths 0.230 to 1.000, incl[from 6.0 through 25]NOTE 1: The changes in width limits with the publication of A635/A635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide, as that material is now covered by Specification A568/A568M – 06a. The purchaser is advised to discuss this change with the supplier.1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.1.5 For the purposes of determining conformance with this and the appropriate product specifications referenced in 1.2, measured values, calculated values, and observed values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.1.5.1 Ordered values, identified in tables, specified such as over 30 through 48, or 30 exclusive to 48 inclusive, covers all ordered values specified as 30.1, 30.01, 30.001, etc., up to and including 48.000 etc., but does not cover ordered values specified as 30.000 etc. or less, nor does it cover ordered values specified as 48.1, 48.01, 48.001, etc., in accordance with the absolute method of Practice E29.1.6 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.NOTE 2: The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.8 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1.1 This specification covers hot-rolled, heavy-thickness, high-strength, low-alloy columbium, or vanadium hot-rolled sheet and strip, or combinations thereof, in coils beyond the size limits of Specification A607. This material is intended for miscellaneous applications where greater strength and savings in weight are important. The material is available as two classes. They are similar in strength level, except that Class 2 offers improved weldability and more formability than Class 1. Atmospheric corrosion resistance of these steels is equivalent to plain carbon steels. With copper specified, the atmospheric corrosion resistance is somewhat enhanced. Note 1-For methods of establishing the atmospheric corrosion resistance of low-alloy steels see Guide G101. 1.1.1 This material is available only in coils described as follows: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip Over 8 to 12 0.230 to 0.750, incl (Over 200-300) (Over 6.0 to 19) Sheet Over 12 to 48 0.230 to 0.750, incl (Over 300-1200) (Over 6.0 to 19) Over 48 (Over 1200) 0.180 to 0.750, incl (Over 4.5 to 19) 1.2 Sheet and strip in coils of sizes noted in 1.1 can be included in this specification only with the following: 1.2.1 The material is not to be converted into steel plates for structural or pressure vessel use. 1.2.2 This specification is not applicable to the steels covered by Specification A635/A635M. 1.2.3 The dimensional tolerances of Specification A635/ A635M are applicable to material produced to this specification. 1.2.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.2.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers heavy thickness high-strength, low-alloy hot-rolled sheet and strip, in coils beyond the size limits of Specification A715. The product has improved formability when compared with steels covered by Specification A935/A935M. The product is furnished only as coils and is available in four-strength levels, Grades 50, 60, 70 and 80 (345, 415, 485, 550) (corresponding to minimum yield strength (see Table 1)). The steel is killed, made to a fine grain practice, and includes microalloying elements such as columbium, titanium, vanadium, zirconium, etc. The steel may be treated to achieve inclusion control. The product is intended for miscellaneous applications where higher strength, savings in weight, improved formability, and weldability are important. Atmospheric corrosion resistance of these steels is equivalent to plain carbon steels. With copper specified, the atmospheric corrosion resistance is somewhat enhanced. Note 1-For methods of establishing the atmospheric corrosion resistance of low-alloy steels, see Guide G101. 1.1.1 This material is available only in coils described as follows: Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip Over 8 to 12 (Over 200-300) 0.230 to 0.750, incl (Over 6.0 to 19) Sheet Over 12 to 48 (Over 300-1200) 0.230 to 0.750, incl (Over 6.0 to 19) Over 48 (Over 1200) 0.180 to 0.750, incl (Over 4.5 to 19) 1.2 Sheet and strip in coils of sizes noted in 1.1 can be included in this specification only with the following: 1.2.1 The material is not to be converted into steel plates for structural or pressure vessel use. 1.2.2 This specification is not applicable to the steels covered by Specification A635/A635M. 1.2.3 The dimensional tolerances of Specification A635/ A635M are applicable to material produced to this specification. 1.2.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming. 1.2.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

定价： 0元 / 折扣价： 0 元

This specification covers the general, physical, chemical, and performance requirements for supplemental coolant additives for use as precharging coolants in the cooling systems of heavy-duty engines. Test solutions shall be standard corrosive water, ethylene or propylene glycol in standard corrosive water, and NaCl dissolved in a solution of glycol in deionized water. These test solutions shall comply to the specific limits for the following requirements: corrosion in glassware mass loss; simulated service test mass loss; foaming; water pump cavitation erosion-corrosion rating; corrosion of cast aluminum alloys at heat-rejecting surfaces; ultrasonic cavitation resistance; supplemental coolant additive-glycol base coolant compatibility; hot surface scaling and deposits resistance; effect on nonmetals; storage stability; ash, chloride ion, and silicon contents; pH in distilled water; reserve alkalinity; and the effect on vehicle finish.1.1 This specification covers the general, physical, chemical, and performance requirements for Supplemental Coolant Additives (SCAs) at a precharged level in the cooling systems of heavy-duty engines.NOTE 1: After precharging, SCAs are customarily used periodically to service cooling systems at 1/4 to 1/3 the precharged dosage to compensate for additives lost through dilution and depletion.1.2 The SCA products meeting this specification are intended for use with water, with recommended dilutions of coolant concentrates, with prediluted engine coolants, or to upgrade the performance of light-duty engine coolants to meet the heav-duty requirements of Specification D6210. Engine coolant products shall be of the low-silicate type and, if ethylene glycol based, shall meet Specification D4985. Propylene glycol base low-silicate type coolant products may also be used, if these materials meet the chemical and performance requirements of Specification D4985.1.3 The SCA concentrate, before dissolution, may be in either liquid, solid, or slurry form. The form is as agreed upon between the manufacturer and the user.1.4 The values stated in SI units are to be regarded as standard. The inch-pound units in parentheses are approximate equivalents provided for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the testing and requirements of extruded and compression molded polytetrafluoroethylene (PTFE) rods and heavy-walled tubing manufactured from virgin or reprocessed PTFE resin. Covered here are three types of PTFE fluorocarbon materials as follows: Type I (premium), materials having maximum physical and electrical properties to meet rigid requirements; Type II (general purpose), materials having properties required of general electrical, mechanical, and chemical applications; and Type III, materials for noncritical chemical, electrical, and mechanical applications. These types are further subdivided into two grades, and even further into four classes as appropriate. Sampled specimens shall be appropriately tested on the following: workmanship and appearance (color, finish, and internal defects); specific gravity; tensile strength and elongation; dielectric strength; dimensional stability; and melting point.1.1 This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D4894 and reprocessed PTFE resin (as defined in Guide D7209).1.2 The specification covers all sizes of rod, tubing, and basic shapes with a wall thickness of 1.6 mm (1/16 in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial ram extrusion practices.NOTE 1: This specification and ISO/DIS 13000-1 (1997) and ISO/DIS 13000-2 (1997) differ in approach, however, data obtained using either are technically equivalent.NOTE 2: For compression molded PTFE materials, see Specification D3294. Material that can be certified to Specification D3294 may be substituted for Specification D1710, however the reverse in not true.1.3 The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.1.4 The following precautionary caveat pertains to the test methods portion, Section 12, only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车