5.1 This test method provides a standard laboratory procedure for measuring and comparing the burning rates of polymeric materials under specified controlled conditions.5.2 The rate of burning is affected by such factors as density, direction of rise, and type and amount of surface treatments. The thickness of the finished specimens must also be taken into account. These factors must be considered in order to compare materials on the same basis.5.3 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.1.1 This test method is intended for use as a small-scale laboratory procedure for comparing the relative horizontal burning rates of polymeric materials used in occupant compartments of motor vehicles.1.2 During the course of combustion, gases or vapors, or both, are evolved that are potentially hazardous to personnel. Adequate precautions shall be taken to protect the operator.1.3 Units—The values stated in SI units are to be regarded as standard.1.4 This test method, Federal Safety Standard MVSS 302, SAE J369, and ISO 3795 address the same subject matter, but differ in technical content.1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.NOTE 1: There is no known ISO equivalent to this standard.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

Update #1 was published as notification that this is now a National Standard of Canada This PDF includes Update #1 1. Scope 1.1 This Standard specifies (a) general design requirements; (b) performance requirements; (c) test methods; (d) requi

定价： 546元 / 折扣价： 465 元

This specification covers emergency conditions, occupant safety and accommodations for occupants and cargo. The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this standard as part of a certification plan.1.1 This specification addresses emergency conditions, occupant safety and accommodations for occupants and cargo.1.2 The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this standard as part of a certification plan. For information on which CAA regulatory bodies have accepted this standard (in whole or in part) as a means of compliance to their airworthiness regulations (Hereinafter referred to as “the Rules”), refer to ASTM F44 webpage (www.ASTM.org/COMITTEE/F44.htm) which includes CAA website links.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 Each facility rating scale in this classification provides a means for estimating the level of serviceability of a building or facility for one topic of serviceability, and for comparing that level against the level of any other building or facility.4.2 This classification can be used for comparing how well different buildings or facilities meet a particular requirement for serviceability. It is applicable despite differences such as location, structure, mechanical systems, age, and building shape.4.3 This classification can be used to estimate the amount of variance of serviceability from target or from requirement, for a single office facility, or within a group of office facilities.4.4 This classification can be used to estimate the following: (1) the serviceability of an existing facility for uses other than its present use; (2) the serviceability (potential) of a facility that has been planned but not yet built; and (3) the serviceability (potential) of a facility for which a remodeling has been planned.4.5 The use of this classification does not result in building evaluation or diagnosis. Building evaluation or diagnosis generally requires a special expertise in building engineering or technology and the use of instruments, tools, or measurements.4.6 This classification applies only to facilities that are building constructions or parts thereof. (While this classification may be useful in rating the serviceability of facilities that are not building constructions, such facilities are outside the scope of this classification.)4.7 This classification is not intended for, and is not suitable for, use for regulatory purposes, nor for fire hazard assessment or fire risk assessment.1.1 This classification covers pairs of scales for classifying an aspect of the serviceability of an office facility, that is, the capability of an office facility to meet certain possible requirements to protect occupant assets.1.2 Each pair of scales, shown in Figs. 1-8, printed side by side on a page, are for classifying one topic of serviceability within that aspect of serviceability. Each paragraph in an Occupant Requirement Scale (see Figs. 1-8) summarizes one level of serviceability on that topic that occupants might require. The matching entry in the Facility Rating Scale (see Figs. 1-8) is a translation of the requirement into a description of certain features of a facility that, taken in combination, indicate that the facility is likely to meet that level of required serviceability.FIG. 1 Scale A.8.1 for Control of Access from Building Public Zone to Occupant Reception ZoneFIG. 1 Scale A.8.1 for Control of Access from Building Public Zone to Occupant Reception Zone (continued)FIG. 2 Scale A.8.2 for Interior Zones of SecurityFIG. 2 Scale A.8.2 for Interior Zones of Security (continued)FIG. 3 Scale A.8.3 for Vaults and Secure RoomsFIG. 3 Scale A.8.3 for Vaults and Secure Rooms (continued)FIG. 4 Scale A.8.4 for Security of Cleaning Service SystemsFIG. 4 Scale A.8.4 for Security of Cleaning Service Systems (continued)FIG. 5 Scale A.8.5 for Security of Maintenance Service SystemsFIG. 6 Scale A.8.6 for Security of Renovations Outside Active HoursFIG. 6 Scale A.8.6 for Security of Renovations Outside Active Hours (continued)FIG. 7 Scale A.8.7 for Systems for Secure GarbageFIG. 8 Scale A.8.8 for Security of Key and Card Control Systems1.3 The entries in the Facility Rating Scale (see Figs. 1-8) are indicative and not comprehensive. They are for quick scanning, to estimate approximately, rapidly, and economically, how well an office facility is likely to meet the needs of one or another type of occupant group over time. The entries are not for measuring, knowing, and evaluating how an office facility is performing.1.4 This classification can be used to estimate the level of serviceability of an existing facility. It can also be used to estimate the serviceability of a facility that has been planned but not yet built, such as one for which single-line drawings and outline specifications have been prepared.1.5 This classification indicates what would cause a facility to be rated at a certain level of serviceability, but it does not state how to conduct a serviceability rating nor how to assign a serviceability score. That information is found in Practice E1334. The scales in this classification are complementary to and compatible with Practice E1334. Each requires the other.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 This practice is applicable to all interior and exterior installed building products in the use phase of the product, specifically in the form present in the occupied building. This practice does not cover products during installation processes since those exposures are covered by occupational regulations.4.2 This practice specifies the required information to include in the OESR screening report for product decision makers to assess the potential for occupant health exposure from installed building products in an occupied building operated under normal and anticipated conditions of use.4.3 Fundamental to the selection and use of building products is the consideration of the likelihood of occupant exposure and possible risk to substances in those installed building products.4.4 This practice does not purport to offer full risk information, nor does it purport to be equivalent to an exposure or risk assessment. Rather, it provides screening to inform the product decision maker about conditions that could generate additional discussions with manufacturers or others.4.5 The informational requirements for an OESR are identified in Section 5.4.6 For substances with hazard classifications in 5.3, the OESR informs product decision makers about substances in an installed building product that might trigger a hazard warning to a user or building occupant. This information is designed to help the product decision maker determine whether added information is needed to evaluate exposure and risk more fully in the context of the installed building product’s specific use or application.4.7 The OESR screening report is required to be updated based on the requirements in 9.3.4.8 The OESR is completed by last manufacturer of the building product; this is the manufacturer offering the external or internal building product to the market. This manufacturer may need to obtain information from other manufacturers in its supply chain.NOTE 1: The manufacturer offering the building product to the market is aware of the form, function, and likely uses of the building product under normal conditions of use. If the product contains hazardous substance(s), it is likely that the manufacturer has information about the hazards from the product under foreseeable emergencies in compliance with OSHA requirements.1.1 This practice provides the information required for publishing a screening report for occupant exposure from substances in installed building products (OESR) to communicate possible human health impacts in an occupied building to product specifiers, building owners, and others.1.2 This practice is applicable to all interior and exterior building products in the form used and incorporated into an occupied building.1.3 An article going into the construction market that has potential hazards based upon an evaluation of the United Nations Globally Harmonized System of Classification and Labelling of Chemicals (GHS) (1)2 mixtures guidance is included in the scope of this practice.1.4 This practice does not cover product fabrication or installation processes because these are subject to worker safety and health regulations and law.1.5 The final building product manufacturer offering the building product to the market or agent is responsible for providing this information and completing this report.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车