This specification covers the requirements for chromium diffusion of metals applied by pack cementation process. The four classes of chromium diffusion coating, defined by the type of base metal, are as follows: Class I (carbon steels); Class II (low-alloy steels); Class III (stainless steels); and Class IV (nickel-based alloys). Specimens shall adhere to processing requirements such as substrate preparation, materials (masteralloys, activators, and inert fillers), loading, furnace cycle, post cleaning, post straightening, visual inspection, and marking and packaging. Specimens shall also adhere to coating requirements such as diffusion thickness, decarburization, chromium content, appearance, and mechanical properties (tensile strength, and macro- and micro-hardness).1.1 This specification covers the requirements for chromium diffusion of metals by the pack cementation method. Pack diffusion employs the chemical vapor deposition of a metal which is subsequently diffused into the surface of a substrate at high temperature. The material to be coated (substrate) is immersed or suspended in a powder containing chromium (source), a halide salt (activator), and an inert diluent such as alumina (filler). When the mixture is heated, the activator reacts to produce an atmosphere of chromium halides which transfers chromium to the substrate for subsequent diffusion. The chromium-rich surface enhances corrosion, thermal stability, and wear-resistant properties.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
定价: 515元 / 折扣价: 438 元 加购物车
This specification covers the requirements for aluminum diffusion of metals applied by pack cementation process. The three classes of aluminum diffusion coating, defined by the type of base metal, are as follows: Class I (carbon and low alloy steels); Class II (stainless steels); and Class III (nickel-based alloys). Specimens shall adhere to processing requirements such as substrate preparation, high and low activity pack mix, materials (masteralloys, activators, and inert fillers), loading, furnace cycle, post cleaning, diffusion heat treatment, post straightening, visual inspection, and marking and packaging. Specimens shall also adhere to coating requirements such as diffusion thickness, aluminum content, appearance, and mechanical properties (tensile strength, and macro- and micro-hardness).1.1 This specification covers the requirements for aluminum diffusion of metals by the pack cementation method. Pack diffusion employs the chemical vapor deposition of a metal which is subsequently diffused into the surface of a substrate at high temperature. The material to be coated (substrate) is immersed or suspended in a powder containing aluminum (source), a halide salt (activator), and an inert diluent such as alumina (filler). When the mixture is heated, the activator reacts to produce an atmosphere of aluminum halides which transfers aluminum to the substrate for subsequent diffusion. The aluminum-rich surface enhances corrosion, thermal stability, and wear-resistant properties.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
定价: 515元 / 折扣价: 438 元 加购物车
This specification covers in-situ applied, single-pack, moisture-triggered, aliphatic polyurethanes intended to form an elastomeric single-ply roofing membrane, once cured. The cured membrane may or may not contain a reinforcing material. The product, as manufactured, shall be in liquid form for application by brush, roller, or spray equipment. In-place roof system design criteria such as fire resistance, material compatibility, and uplift resistance, among others, are beyond the scope of this specification. Wet coatings shall be tested and shall conform to liquid property requirements as to viscosity, volume and weight of solids, and sag resistance. Dry films shall also be tested and conform to physical property requirements, as follows: tensile strength; elongation; accelerated weathering; water vapor transmission permeability and permeance; mandrel bend flexibility; tear resistance; Taber abrasion resistance; indentation hardness; dynamic and static puncture resistance; and adhesion bond strength.1.1 This specification covers in-situ applied, single-pack, moisture-triggered, aliphatic polyurethanes intended to form an elastomeric single-ply membrane, once cured. The cured membrane may or may not contain a reinforcing material. 1.2 Single-pack, moisture-triggered, aliphatic polyurethanes are characterized by their ability to use moisture to trigger the curing process only. 1.3 The tests and property limits used to characterize the liquid material and cured membrane are values intended to ensure minimum quality. In-place roof system design criteria such as fire resistance, material compatibility, and uplift resistance, among others, are factors that shall be considered but are beyond the scope of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.