5.1 This test method provides accurate data for evaluation of the optical properties of the glass being inspected.5.2 The procedure described is useful for observing the roll wave introduced during the tempering process of flat architectural glass. (1)5.3 This test method is also useful for inspection of laminated and tempered automotive glass in transmitted light, in both flat and curved geometries.1.1 This test method covers the determination of optical distortion of heat-strengthened and fully tempered architectural glass substrates which have been processed in a heat controlled continuous or oscillating conveyance oven. See Specifications C1036 and C1048 for discussion of the characteristics of glass so processed. In this test method the reflected image of processed glass is photographed and the photographic image analyzed to quantify the distortion due to surface waviness. The test method is also useful to quantify optical distortion observed in transmitted light in laminated glass assemblies.1.2 The values stated in either SI units or inch-pound units are regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 There is no known ISO equivalent to this test method.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This guide is intended to assist potential users in the search for, evaluation of, and acquisition of remotely sensed aerial photography or imagery, or both, to be used for the purpose of establishing the historic site-use and other interpretable surface or near-surface conditions regionally, locally, or at a specified project location. 1.2 The instructions given in this guide identify sources of photography and imagery, and provide information pertaining to the specifications, characteristics, and availability of these data. 1.3 The major sources considered are restricted to federal and state organizations only. The sources described do not represent all possible sources of interest for environmental and engineering applications. 1.4 The values stated in both inch-pound and SI units are to be regarded separately as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 Particle characterization, especially particle size distribution, has been an important parameter for quality control (QC) and research and development (R&D) in a very wide variety of industries and markets, anywhere a particulate system is a final product or an intermediate constituent somewhere in the process. But size alone is not a sufficient morphological measurement to use to understand many factors of the complete particle morphology of particulate systems and their effects on other properties. This information is expected to contribute to the understanding of the effects of shape on powder spreadability and flowability in the creation of the bed in powder bed fusion AM and the density and porosity of the final AM parts (definitions in ISO/ASTM 52900 and Terminology B243). Ultimately, specifications can be developed for quality control (QC) tolerances for these shape parameters that can be measured with a straightforward, fast automated analysis1.1 This guide explains how to characterize the quality of metal powder feedstock to additive manufacturing (AM) relative to the powder shape using automated static or dynamic image analysis by optical photography. This guide will describe the method(s) to measure powder shape parameters that can identify potentially detrimental powder characteristics and specifically describe how to identify and quantify the proportion of agglomerates/satellites and other irregularly shaped non-spherical powder particles in a powder batch.1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车