微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读

This specification covers nominally 17.5% Cr free-machining ferritic stainless soft magnetic alloy produced or supplied expressly in cold-finished bar form for use in magnetic cores and other parts requiring a corrosion-resistant, high permeability, low-coercivity steel. This specification does not cover either cast parts or parts produced by powder metallurgy techniques. Two specific alloy types are covered distinguished by different silicon levels. Required measurements include chemical analysis and dc magnetic property measurement. The magnetic properties depend both on the grade and the dimensions. Apart from the requirements, the specification contains useful appendices discussing the magnetic testing of these alloys and typical magnetic and physical properties.1.1 This specification covers free-machining ferritic stainless soft magnetic alloy produced or supplied expressly in cold-finished bar form for use in magnetic cores and other parts requiring a high permeability, low-coercivity stainless steel.1.1.1 This specification does not cover either cast parts or parts produced by powder metallurgy techniques.1.2 Two specific alloy types are covered. The primary constituents are shown in Table 1. These types have corrosion resistance similar to AISI Type 430F and Type 430F, Specification A582/A582M.1.3 This specification covers only these alloy types supplied in cold-finished bars in cross-sectional shapes such as rounds, squares, hexagons, and octagons with diameters (diagonals) greater than or equal to 6.35 mm (0.250 in.) and less than or equal to 41.5 mm (1.63 in.).21.4 Certain cold-finished round bar products are capable of being supplied mill annealed to required magnetic properties such as low coercivity. The size range that can be mill annealed is from 6.35 to 41.5 mm (0.250 to 1.63 in.). Other products of these alloys cannot be mill annealed to produce equivalently low coercivity; hence, the final machined parts should be heat treated as recommended by the producer.1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 515元 / 折扣价: 438 加购物车

在线阅读 收 藏
ASTM A867-19 Standard Specification for Iron-Silicon Relay Steels Active 发布日期 :  1970-01-01 实施日期 : 

This specification covers wrought iron-silicon (Fe-Si) relay steels that are generally used in the manufacture of electromechanical devices, such as relays and solenoids, requiring higher electrical resistivity, higher permeability, and lower coercivity and residual magnetism than provided by either carbon steels or soft magnetic low-carbon irons. Available forms and conditions are forging billet, hot-rolled product, cold-finished bars, strip, and wire. These steels are not the same as the flat-rolled non-oriented or grain oriented iron-silicon electrical steels covered by ASTM Specifications A 677, A 683 and A 876. The steels covered in this specification have nominal silicon contents of 1.1, 2.3 and 4.0 % Si. Both the 1.1 and 2.3 % Si types are also available in an enhanced machinability composition. Along with chemical composition, steels produced to this specification must meet a specified maximum value of coercive field strength when heat treated according to this specification. Appendices are given containing typical magnetic, physical and mechanical properties and heat treatment.1.1 This specification covers wrought iron-silicon (Fe-Si) steels that are generally used in the manufacture of electromechanical devices, such as relays and solenoids, requiring higher electrical resistivity, higher permeability, and lower coercivity and residual magnetism than provided by either carbon steels or soft magnetic low-carbon irons. The steels covered in this specification are:Steel Type Nominal Composition   1 1.1 % Si-Fe1F 1.1 % Si-Fe free machining2 2.3 % Si-Fe2F 2.3 % Si-Fe free machining3 4.0 % Si-Fe1.2 This specification covers steels in the form and condition required for fabrication into parts. The fabricated parts typically require a final heat treatment to obtain the desired magnetic performance. The term mill annealed as used in this specification applies to a heat treatment, typically applied by the producer, intended to improve formability. The mill anneal does not provide the optimum magnetic performance and is not intended to replace the need for the finish annealing of parts.1.3 This specification covers steels in the form of forging billets, hot-rolled bar and strip, cold-finished bar, wire, and cold-rolled strip in thicknesses up to 6.35 mm (0.250 in.).1.4 This specification does not cover electrical sheet steels used in transformer and motor laminations. Please refer to Specifications A677, A683, A726, A876, and A1086 for standards pertaining to these material types.1.5 This specification does not cover powder metallurgy materials capable of being processed into magnetic core components having similar silicon contents.1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard.1.6.1 There are selected values presented in two units, both of which are in acceptable SI units. These are differentiated by the word “or,” as in “μΩ-cm, or, Ω-m.”1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏
YD/T 3785-2020 LTE数字蜂窝移动通信网中继(Relay)系统设备测试方法 现行 发布日期 :  2020-12-09 实施日期 :  2021-01-01

本标准适用于TD-LTE和LTEFDD数字蜂窝移动通信网中继系统设备

定价: 无文本 / 折扣价: 0

在线阅读 收 藏
YD/T 3784-2020 LTE数字蜂窝移动通信网中继(Relay)系统设备技术要求 现行 发布日期 :  2020-12-09 实施日期 :  2021-01-01

本标准适用于TD-LTE和LTEFDD数字蜂窝移动通信网中继系统设备

定价: 无文本 / 折扣价: 0

在线阅读 收 藏
4 条记录,每页 10 条,当前第 1 / 1 页 第一页 | 上一页 | 下一页 | 最末页  |     转到第   页