定价： 481元 / 折扣价： 409 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 260元 / 折扣价： 221 元

定价： 260元 / 折扣价： 221 元

定价： 260元 / 折扣价： 221 元

定价： 0元 / 折扣价： 0 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

This specification covers two types of factory prepared reinforced bituminous flashing sheets used for roofing and waterproofing systems. The bitumen used may be asphalt, coal-tar pitch, or polymer modified bitumen. The reinforcement may include any one or a combination of organic (wood fiber), polyester, or glass fiber felts, woven fabrics, or thermoplastic films. Fine mineral powders, granules, or metal foils may be used as surfacing. Specimens shall be sampled, be tested for, and consequently conform to dimensional and physical properties, as follows: mass; thickness; load-strain properties; impact resistance; tear strength and resistance; flexibility; breaking load; and elongation at break. Calculation procedures for the mean, estimated standard deviation, and mean variance of test values from specimens tested before and after heat conditioning are also detailed.1.1 This specification covers factory-prepared reinforced bituminous sheet used in flashing. The bitumen used may be asphalt, coal-tar pitch, or polymer-modified bitumen. The reinforcement may include any one or a combination of organic (wood fiber), polyester, or glass fiber felts, woven fabrics, or thermoplastic films. Fine mineral powders, granules, or metal foils may be used as surfacing.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 The following precautionary statement pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 This practice shall be used for specific procedures used in preparing rubber compounds for quality control of production, for research and development purposes, and for comparison of different materials.1.1 This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing. It also specifies the mixing equipment, general mixing procedures, vulcanization equipment and procedures.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see 5.4.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

Update No. 1 was published as notification that this is now a National Standard of Canada This PDF includes Update No. 1 Preface This is the second edition of CSA A123.16, Asphalt-coated glass-base sheets. It supersedes the first edition, publis

定价： 592元 / 折扣价： 504 元

Update No. 1 was published as notification that this is now a National Standard of Canada This PDF includes Update No. 1 1 Scope 1.1 This Standard deals with asphalt-coated roofing sheets composed of asphalt-saturated organic felt coated on one o

定价： 592元 / 折扣价： 504 元

This specification covers the requirements for flat asbestos-cement sheets designed for use in industrial, commercial, and general building purposes. Each sheet should be composed of a combination of asbestos fiber and Portland cement or Portland blast-furnace slag cement. Curing agents, water-repellent substances, mineral fillers, coatings, pigments, or minerals may be added to the material. All the materials should conform to the requirements on flexural strength, water absorption, workmanship, finish, color, and efflorescence.1.1 This specification covers asbestos-cement sheets in flat form designed for industrial, commercial, and general building purposes, of the following types:1.1.1 Flat Sheets, Type F (Flexible)—An asbestos-cement flat sheet suitable for exterior and interior use, where a board having higher strength and density, smoother surface, greater flexibility, and lower moisture absorption is desired.1.1.2 Flat Sheets, Type U (Utility)—An asbestos-cement flat sheet suitable for exterior and interior use, having sufficient strength for general utility and construction purposes, and where a board having maximum flexibility, highest density, smoother surface, and lower moisture absorption is not essential.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysotile asbestos, refer to “Safe Use of Chrysotile: A Manual on Preventive and Control Measures.”21.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 This test method is used to determine the dimensional changes and physical stability of the product upon exposure to specified cyclic thermal conditions. It is also useful in determining the integrity of the bond between the metal foil and the SBS-modified bituminous compound.1.1 This test method covers the measurement of movement due to cyclic thermal exposure of SBS (styrene-butadiene-styrene)-modified bituminous sheets with a factory-applied metal foil surface.1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车