微信公众号随时随地查标准

QQ交流1群(已满)

QQ群标准在线咨询2

QQ交流2群

购买标准后,可去我的标准下载或阅读
CAN3-D313-M85 (R2002) Trailer Running Gear 现行 发布日期 :  1970-01-01 实施日期 : 

1. Scope 1.1 This Standard provides a testing procedure for defining a minimum level of structural adequacy and performance capability for running gear used under trailers, sectional homes, and mobile homes, but excludes trailers equipped with full ai

定价: 455元 / 折扣价: 387

在线阅读 收 藏

This specification covers trailer cycles, intended to be pulled behind bicycles, with seat post attachment, for transporting children. It includes test methods for confirming that this specification is satisfied.1.1 This specification covers trailer cycles, intended to be pulled behind bicycles, with seat post attachment, in order to transport children. It includes test methods for confirming that this specification is satisfied.1.2 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only.1.3 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests). This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

5.1 The measured values are traction properties of tires obtained with the towed trailer described here on a given road surface, under given environmental conditions (ambient and road surface temperature, humidity, wind speed and direction, purity and film depth of water used to wet the road surface). They are carried out in accordance with the stated test procedures and reflect the performance of the total tire-vehicle environmental system. A change in any of these factors may change the measurements on a subsequent run of the test.5.2 These test methods are suitable for research and development purposes, where tires are compared during a single series of tests. They may not be suitable for regulatory statutes or specification acceptance, because the values obtained may not necessarily agree or correlate either in rank order or absolute traction performance level with those obtained on other road surfaces (or the same surface after additional wear), under other environmental conditions, or other towed trailers, or other test devices, or with results obtained with other test procedures.1.1 This test method covers the measurement of braking traction of tires designed for passenger cars or light trucks. Such braking traction measurements are applicable to conditions wherein the vehicle is traveling straight ahead on a wet, paved surface.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

1.1 This specification covers the general performance requirements for the Type II Cargo Bed Cover (CBC). The Type II Cargo Bed Cover is a removable general purpose rigid wall enclosure that is mounted on the M105A2 Trailer, Cargo: 1.5 Ton, 2 Wheel. The Type II CBC provides environmental protection and security for mission equipment and items of general transport.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parenthesis are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 590元 / 折扣价: 502 加购物车

在线阅读 收 藏

This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/M1095, 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport. Materials shall be tested and shall conform to the general requirements such as first article, conformance, operating requirements, support and ownership requirements, environmental requirements, and interface and operability requirements.1.1 This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a removable general purpose rigid wall enclosure that is mounted to the following model 5 ton cargo trucks: (1) the M923 Medium Tactical Vehicle (MTV) and (2) the M1083 MTV. It also can be mounted on the M1095 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价: 646元 / 折扣价: 550 加购物车

在线阅读 收 藏
5 条记录,每页 10 条,当前第 1 / 1 页 第一页 | 上一页 | 下一页 | 最末页  |     转到第   页