定价： 481元 / 折扣价： 409 元

定价： 345元 / 折扣价： 294 元

定价： 481元 / 折扣价： 409 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 345元 / 折扣价： 294 元

定价： 345元 / 折扣价： 294 元

定价： 481元 / 折扣价： 409 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 156元 / 折扣价： 133 元

定价： 156元 / 折扣价： 133 元

定价： 156元 / 折扣价： 133 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

5.1 This guide provides an alternative way to measure the porosity of catalytic materials without the use of mercury porosimetry. It is useful for research and development as well as quality control purposes. (See Test Methods D4284 and D6761.)1.1 This guide describes how to measure the pore volume of catalytic materials by water immersion with the excess water removed with a centrifuge. The measured pore volume is converted to the dry pore volume by using the loss on ignition (LOI) of the material. It is generally applicable to both powdered materials and particles greater than about 1 mm.1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 For custody transfer and other purposes, it is frequently necessary to convert a component analysis of light hydrocarbon mixture from one basis (either gas volume, liquid volume, or mass) to another.3.2 The component distribution data of light hydrocarbon mixtures can be used to calculate physical properties such as relative density, vapor-pressure, and calorific value. Consistent and accurate conversion data are extremely important when calculating vapor, liquid, or mass equivalence.1.1 This practice describes the procedure for the interconversion of the analysis of C5 and lighter hydrocarbon mixtures to gas-volume (mole), liquid-volume, or mass basis.1.2 The computation procedures described assume that gas-volume percentages have already been corrected for nonideality of the components as a part of the analytical process by which they have been obtained. These are numerically the same as mole percentages.1.3 The procedure assumes the absence of nonadditivity corrections for mixtures of the pure liquid compounds. This is approximately true only for mixtures of hydrocarbons of the same number of carbon atoms, and in the absence of diolefins and acetylenic compounds.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车