
【国外标准】 Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This specification establishes quality requirements and provides a basis for common understanding among producers, distributors, and users.4.2 It is not intended that all paints meeting the requirements be identical nor of uniform excellence in all respects. Variations in manufacture, not covered by this specification, may cause some artists to prefer one brand over another, either of which may be acceptable under this specification.AbstractThis specification establishes requirements for composition, physical properties, performance, and labeling of artists' oil, resin-oil, and alkyd paints. This specification covers pigments, vehicles, and additives. Requirements are included for pigment identification, lightfastness, consistency, and drying time. The different labelling requirements for artists' oil paints, resin-oil, and alkyd paints are presented in details. The quality assurance method for artists' oil paints and artists' resin-oil paints are presented in details. The quality assurance methods for artists' alkyd paints are presented. The lightfastness of the paints shall be tested to meet the requirements prescribed. Lightfastness categories shall be assign to meet the requirements prescribed.1.1 This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ oil, resin-oil, and alkyd paints.1.2 This specification covers pigments, vehicles, and additives. Requirements are included for pigment identification, lightfastness, consistency, and drying time.1.3 Table 1 lists some pigments meeting the lightfastness requirements in this specification. In order to identify other pigments that meet these requirements, instructions are given for test specimen preparation. Test methods for determining relative lightfastness are referenced.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.5 This pertains only to the test method found in Section 8. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D4302-14(2021)
标准名称:
Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints
英文名称:
Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E1815-18(2023) Standard Test Method for Classification of Film Systems for Industrial Radiography
- ASTM E1820-23b Standard Test Method for Measurement of Fracture Toughness
- ASTM E1822-21 Standard Test Method for Fire Testing of Stacked Chairs
- ASTM E1823-23 Standard Terminology Relating to Fatigue and Fracture Testing
- ASTM E1826-23 Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels
- ASTM E1827-22 Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
- ASTM E1829-14(2020) Standard Guide for Handling Specimens Prior to Surface Analysis
- ASTM E1832-08(2017) Standard Practice for Describing and Specifying a Direct Current Plasma Atomic Emission Spectrometer
- ASTM E1834-18 Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry
- ASTM E1835-14(2022) Standard Test Method for Analysis of Nickel Alloys by Flame Atomic Absorption Spectrometry
- ASTM E1845-23 Standard Practice for Calculating Pavement Macrotexture Mean Profile Depth
- ASTM E1851-21 Standard Test Method for Electromagnetic Shielding Effectiveness of Durable Rigid Wall Relocatable Structures
- ASTM E1854-19 Standard Practice for Ensuring Test Consistency in Neutron-Induced Displacement Damage of Electronic Parts
- ASTM E1856-13(2021) Standard Guide for Evaluating Computerized Data Acquisition Systems Used to Acquire Data from Universal Testing Machines
- ASTM E1857-97(2021) Standard Guide for Selection of Cleaning Techniques for Masonry, Concrete, and Stucco Surfaces