
【国外标准】 Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 The four-ball wear-test method can be used to determine the relative wear-preventing properties of greases under the test conditions and if the test conditions are changed the relative ratings may be different. No correlation has been established between the four-ball wear test and field service. The test method cannot be used to differentiate between Extreme Pressure (EP) and Non-Extreme Pressure (Non-EP) Greases.41.1 This test method covers the determination of the wear preventive characteristics of greases in sliding steel-on-steel applications. It is not intended to predict wear characteristics with metal combinations other than steel-on-steel or to evaluate the extreme pressure characteristics of the grease.1.2 The values stated in SI units are to be regarded as the standard except where the test apparatus or consumable parts are only available in other units. In such cases, these will be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D2266-23
标准名称:
Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)
英文名称:
Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D3964-10(2020) Standard Practice for Selection of Coating Specimens for Appearance Measurements
- ASTM D3965-21 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
- ASTM D3966/D3966M-22 Standard Test Methods for Deep Foundation Elements Under Static Lateral Load
- ASTM D3967-23 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens with Flat Loading Platens
- ASTM D3972-09(2015) Standard Test Method for Isotopic Uranium in Water by Radiochemistry
- ASTM D3974-09(2023) Standard Practices for Extraction of Trace Elements from Sediments
- ASTM D3975-93(2019) Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments
- ASTM D3976-22 Standard Practice for Preparation of Sediment Samples for Chemical Analysis
- ASTM D3977-97(2019) Standard Test Methods for Determining Sediment Concentration in Water Samples
- ASTM D3978-21a Standard Practice for Algal Growth Potential Testing with Pseudokirchneriella subcapitata
- ASTM D3981-09a(2016) Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications
- ASTM D3982-21 Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts
- ASTM D3983-98(2019) Standard Test Method for Measuring Strength and Shear Modulus of Nonrigid Adhesives by the Thick-Adherend Tensile-Lap Specimen
- ASTM D3984-19 Standard Specification for Ethane Thermophysical Property Tables
- ASTM D3985-17 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor