
【国外标准】 Standard Test Method for Freezing Point of Aviation Fuels (Automatic Fiber Optical Method)
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 The freezing point of an aviation fuel is an index of the lowest temperature of its utility for certain applications. Solid hydrocarbon crystals can restrict the flow of fuel in the fuel system of the aircraft. The temperature of the fuel in the aircraft tank normally decreases during flight depending on aircraft speed, altitude, and flight duration. The freezing point of the fuel must always be lower than the minimum operational fuel temperature.5.2 Petroleum blending operations require precise measurement of the freezing point.5.3 This test method expresses results with a resolution of 0.1 °C.5.4 This test method eliminates most of the operator time and judgment required by Test Method D2386.5.5 When the specification requires the use of Test Method D2386, do not substitute this test method or any other method.1.1 This test method covers the determination of the temperature below which solid hydrocarbon crystals may form in aviation turbine fuels.NOTE 1: This test method describes an alternative procedure and automatic apparatus which closely mimics the apparatus and procedure described in Test Method D2386.1.2 The measuring range of the apparatus is from –70 °C to 0 °C, however the precision statements were derived only from samples with freezing point temperatures from –60 °C to –42 °C.NOTE 2: Typical aviation fuel has freezing point temperatures in the –60 °C to –40 °C range.1.3 Some results from this test method (14 % of samples included in the 2003 round robin2) incorrectly identified sample contamination where no contaminants were present in the samples (see research report2 for further information).1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D7154-15(2021)e1
标准名称:
Standard Test Method for Freezing Point of Aviation Fuels (Automatic Fiber Optical Method)
英文名称:
Standard Test Method for Freezing Point of Aviation Fuels (Automatic Fiber Optical Method)标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM C117-23 Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
- ASTM C1170/C1170M-20 Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
- ASTM C1173-22 Standard Specification for Flexible Transition Couplings for Underground Piping Systems
- ASTM C1174-20 Standard Guide for Evaluation of Long-Term Behavior of Materials Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste
- ASTM C1177/C1177M-17 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
- ASTM C1178/C1178M-18 Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel
- ASTM C1181/C1181M-17 Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts
- ASTM C1184-23 Standard Specification for Structural Silicone Sealants
- ASTM C1185-23 Standard Test Methods for Sampling and Testing Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards
- ASTM C1186-22e1 Standard Specification for Flat Fiber-Cement Sheets
- ASTM C1190-18(2022) Standard Practice for Location of Test Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick
- ASTM C1193-16(2023) Standard Guide for Use of Joint Sealants
- ASTM C1195-21 Standard Test Method for Absorption of Architectural Cast Stone
- ASTM C1196-20 Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements
- ASTM C12-22a Standard Practice for Installing Vitrified Clay Pipe Lines