
【国外标准】 Standard Test Method for Measurement of Shives in Retted Flax
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Few standards exist to objectively determine flax quality. Shive is the woody core of the stem and has an important effect on quality determination. Shive content will vary depending on the stage of processing and can determine in what products the fiber can be used. Spectroscopic data provide an accurate, precise and rapid determination of the amount of shive in flax fiber.5.1.1 If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed by those laboratories to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples that are as homogeneous as possible are drawn from the material from which the disputed test results were obtained, and are randomly assigned in equal numbers to each laboratory. These results from the two laboratories should be compared using a statistical test for unpaired data, a possibility level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that fiber sample type must be adjusted in consideration of the known bias.5.2 This test method gives data on shive content of retted flax fiber which can be used as a basis for: (1) estimating the net amount of manufacturing fiber obtainable from retted flax fiber; (2) along with other measurements, predicting the quality of flax products, particularly their aesthetic properties; (3) adjusting processing machinery for maximum efficiency in cleaning; and (4) relating shive content to end-product quality and processing efficiency.1.1 This test method covers the measurement of shives in retted flax.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D7076-10(2021)e1
标准名称:
Standard Test Method for Measurement of Shives in Retted Flax
英文名称:
Standard Test Method for Measurement of Shives in Retted Flax标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D5404/D5404M-21 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator
- ASTM D5405/D5405M-98(2021) Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material
- ASTM D5406-22 Standard Practice for Rubber—Calculation of Producer's Process Performance Indexes
- ASTM D5412-93(2017)e1 Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- ASTM D5413-21 Standard Test Methods for Measurement of Water Levels in Open-Water Bodies
- ASTM D5414-95(2020) Standard Test Method for Evaluation of Horizontal Impact Performance of Load Unitizing Stretch Wrap Films
- ASTM D5416-95(2020) Standard Test Method for Evaluating Abrasion Resistance of Stretch Wrap Films by Vibration Testing
- ASTM D542-22 Standard Test Method for Index of Refraction of Transparent Organic Plastics
- ASTM D5420-21 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
- ASTM D5422-17 Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer
- ASTM D5424-23a Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
- ASTM D5425-23 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products
- ASTM D5426-19 Standard Practices for Visual Inspection and Grading of Fabrics Used for Inflatable Restraints
- ASTM D5427-09(2019) Standard Practice for Accelerated Aging of Inflatable Restraint Fabrics
- ASTM D5428-08(2019) Standard Practice for Evaluating the Performance of Inflatable Restraint Modules