
【国外标准】 Standard Test Method for Adhesion of Tire Cords and Other Reinforcing Cords to Rubber Compounds by H-Test Procedure
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Test Method D4776 for the determination of the H-test adhesion of reinforcing cords to rubber compounds may be used for the acceptance testing of commercial shipments of reinforcing cords but caution is advised since information about between-laboratory precision is incomplete. Comparative tests as directed in 5.1.1 may be advisable.5.1.1 In cases of dispute arising from the differences in reported test results when using Test Method D4776 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before testing begins. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in light of the known bias.5.2 This test method is used to measure the force required to extract the cord from a rubber compound test block.5.3 This test method is designed to test the adhesion of textiles that are bonded to rubber compounds. Variables that may contribute to differences in results of this test method include adhesive type, adhesive application procedure, adhesive cure, fiber type, construction of cords, rubber type, rubber cure, and rubber thickness.5.3.1 The deleterious effect of ozone in combination with atmospheric moisture on the ability of adhesives to bond with rubber requires assiduous protection of cords prior to embedment.5.4 The expected range of values which characterize acceptable adhesion can be determined in any cord-rubber combination with experience. For this reason, the purchaser normally establishes a minimum level of adhesion to be obtained by the supplier in either the supplier's laboratory or the purchaser's laboratory using either the supplier's standard rubber compound or the purchaser's rubber compound.1.1 This test method covers the measurement of adhesion of reinforcing cords that are bonded to rubber compounds. This test method is applicable to textile cord structures from both natural and manmade fibers, other than steel. For adhesion testing of steel tire cords, refer to Test Method D2229.1.2 This test method is primarily used to evaluate tire cords, using a suitable tire cord adhesive and a suitable rubber compound. This test method is also used to evaluate (1) tire cord adhesives, and (2) the process of adhesive reaction on the cord using one consistent form of tire cord and one consistent rubber compound. This test method may be used to evaluate cords in industrial hose and belting products and other cord reinforced rubber products.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D4776/D4776M-18
标准名称:
Standard Test Method for Adhesion of Tire Cords and Other Reinforcing Cords to Rubber Compounds by H-Test Procedure
英文名称:
Standard Test Method for Adhesion of Tire Cords and Other Reinforcing Cords to Rubber Compounds by H-Test Procedure标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D4775/D4775M-09(2014) Standard Specification for Identification and Configuration of Prefilled Syringes and Delivery Systems for Drugs (Excluding Pharmacy Bulk Packages) (Withdrawn 2022)
- 下一篇: ASTM D4778-15 Standard Test Method for Determination of Corrosion and Fouling Tendency of Cooling Water Under Heat Transfer Conditions (Withdrawn 2024)
- 推荐标准
- ASTM B615-79(2022) Standard Practice for Measuring Electrical Contact Noise in Sliding Electrical Contacts
- ASTM B616-23 Standard Specification for Refined Rhodium
- ASTM B617-98(2021) Standard Specification for Coin Silver Electrical Contact Alloy
- ASTM B618/B618M-18e1 Standard Specification for Aluminum-Alloy Investment Castings
- ASTM B619/B619M-19(2023) Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
- ASTM B62-17 Standard Specification for Composition Bronze or Ounce Metal Castings
- ASTM B621-21 Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy Rod
- ASTM B622-23 Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube
- ASTM B628-98(2021) Standard Specification for Silver-Copper Eutectic Electrical Contact Alloy
- ASTM B63-07(2018) Standard Test Method for Resistivity of Metallically Conducting Resistance and Contact Materials
- ASTM B631-93(2021) Standard Specification for Silver-Tungsten Electrical Contact Materials
- ASTM B633-23 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
- ASTM B634-14a(2021) Standard Specification for Electrodeposited Coatings of Rhodium for Engineering Use
- ASTM B636/B636M-15(2021) Standard Test Method for Measurement of Internal Stress of Plated Metallic Coatings with the Spiral Contractometer
- ASTM B639-02(2018) Standard Specification for Precipitation Hardening Cobalt-Containing Alloys (UNS R30155 and UNS R30816) Rod, Bar, Forgings, and Forging Stock for High-Temperature Service