
【国外标准】 Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 The success of a waterproofing application depends on, among other things, the type, smoothness, and cleanliness of the concrete surface being coated. This guide describes conditioning or repairing of the concrete surface by the removal or other constructive modification of those surface defects that can affect the performance of the waterproofing system. It covers surface preparation by mechanical, chemical, and blast cleaning methods in order to provide good adhesion between the waterproofing system and the concrete as well as the effect and control of various surface contaminants. It also addresses the evaluation of concrete moisture content to ensure optimal initial bond. (See also ACI 515.)3.2 This guide is not intended to offer guidelines for the selection of a suitable waterproofing system; the use of specific application techniques; or the design and installation of flashing, terminations, expansion joint details, etc. (For definitions of terms, see Terminology D1079.)3.3 This guide is not intended to offer guidelines for the control of water vapor drive through the concrete which could affect long term performance of the bond between the concrete and waterproofing.3.4 The recommended procedures described herein are minimums; the waterproofing materials manufacturer may require more strict or specific procedures for the preparation of concrete surfaces for the application of the manufacturer's specific system.1.1 This guide provides recommendations for the preparation of concrete surfaces prior to the application of adhered (bonded) waterproofing.1.2 This guide is directed primarily toward installations of new concrete, but is also applicable for existing concrete installations. (See also ACI 116 and ACI 546.)1.3 This guide does not apply to loose laid systems, bentonite systems, lead, or the like.1.4 This guide does not apply to applications involving insulating concrete.1.5 This guide does not apply to applications involving lightweight structural concrete.NOTE 1: Once installed, it is difficult to visually identify the difference between normal weight and lightweight concrete. It is recommended that a review of contract documents, concrete batch or delivery tickets or similar effort be performed to identify the concrete type.1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D5295/D5295M-18
标准名称:
Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
英文名称:
Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D5293-20 Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator
- 下一篇: ASTM D5296-19 Standard Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography
- 推荐标准
- AS/NZS 1735.18:2002 Lifts, escalators and moving walks Passenger lifts for private residence - Automatically controlled
- AS/NZS 2111.18:1997 (R2013) Textile floor coverings - Tests and measurements Burning behaviour - Tablet test at ambient temperature
- ASTM 51026-23 Standard Practice for Using the Fricke Dosimetry System
- ASTM 52303-24 Standard Guide for Absorbed-Dose Mapping in Radiation Processing Facilities
- ASTM A1-00(2018) Standard Specification for Carbon Steel Tee Rails
- ASTM A1000/A1000M-17(2023) Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality
- ASTM A1001-18 Standard Specification for High-Strength Steel Castings in Heavy Sections
- ASTM A1002-16(2020) Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
- ASTM A1004/A1004M-99(2018) Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members
- ASTM A1009-18 Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM A101-04(2019) Standard Specification for Ferrochromium
- ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
- ASTM A1012-10(2021) Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins
- ASTM A1015-01(2018) Standard Guide for Videoborescoping of Tubular Products for Sanitary Applications
- ASTM A1016/A1016M-23 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes