
【国外标准】 Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This test method evaluates grab tensile properties of reinforced geomembranes for the purposes of quality control, quality assurance, and research. In order to evaluate the full contribution of the reinforcement, testing is performed parallel to the directions of reinforcement. This test method is an index test and is not intended for design purposes.1.1 This test method is used to measure the grab tensile properties of reinforced geomembranes.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D7004/D7004M-03(2021)
标准名称:
Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes
英文名称:
Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D2561-17(2023) Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
- ASTM D2574-16(2020)e1 Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms
- ASTM D2578-23 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
- ASTM D2582-21 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
- ASTM D2591-07(2020) Standard Test Method for Linear Density of Elastomeric Yarns (Short Length Specimens)
- ASTM D2593-23 Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography
- ASTM D2596-20 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
- ASTM D2598-21 Standard Practice for Calculation of Certain Physical Properties of Liquefied Petroleum (LP) Gases from Compositional Analysis
- ASTM D2616-19 Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale
- ASTM D2619-21 Standard Test Method for Hydrolytic Stability of Hydraulic Fluids (Beverage Bottle Method)
- ASTM D2621-87(2016) Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints
- ASTM D2624-22 Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
- ASTM D263-05(2023) Standard Specification for Chrome Oxide Green Pigment
- ASTM D2633-21 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
- ASTM D2639/D2639M-23 Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer