
【国外标准】 Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 This test method provides a procedure for determining the compliance of steel slags and other materials with specifications or applications that limit permissible expansion of base and subbase aggregates containing components subject to hydration.4.2 This test method can also be used to evaluate the effectiveness of aging or other treatments for reducing the expansive potential of such materials.4.3 This test method is utilized for dense graded materials passing a 25.0 mm (1 in.) sieve. If it is desired to investigate materials larger than a 25.0 mm (1 in.) sieve, Indiana Test Method ITM 219 should be considered.4.4 Test results have not been correlated with field performance, and values obtained do not necessarily indicate expansion that may occur in service conditions. The various methods will provide different numerical results due to differences in severity of the procedures.1.1 This test method covers the determination of potential volume expansion of steel slags that contain components susceptible to hydration and consequent volume increase, such as the free calcium and magnesium oxides.1.1.1 This method is based upon the Cement Autoclave procedure, Test Method C151/C151M, and the California Bearing Ratio procedure, Test Method D1883. This is an aggressive test that can detect both calcium and magnesium expansion potentials. The procedure is also a rapid method typically completed within 24 h.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.NOTE 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8378/D8378M-21
标准名称:
Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave
英文名称:
Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS 4276.21-2005 Water microbiology Examination for coliforms and Escherichia coli - Determination of most probable number (MPN) using enzyme hydrolysable substrates
- AS/NZS 1635.21.1:1995 Methods of test for pressure-sensitive adhesive tape - Mending stability
- AS/NZS 3200.2.21:1994 Approval and test specification - Medical electrical equipment Particular requirements for safety - Infant radiant warmers
- AS/NZS 3200.2.21:1994/Amdt 1:1998 Approval and test specification - Medical electrical equipment - Particular requirements for safety - Infant radiant warmers
- AS/NZS 3350.2.21:1999/Amdt 1:2001 Safety of household and similar electrical appliances - Particular requirements - Storage water heaters
- AS/NZS 3350.2.21:1999/Amdt 3:2004 Safety of household and similar electrical appliances Particular requirements - Storage Water Heaters
- AS/NZS 3350.2.21:1999/Amdt 5:2007 Safety of household and similar electrical appliances Particular requirements - Storage water heaters (IEC 60335-2-21:1997, MOD)
- AS/NZS 3750.21:2008 Paints for steel structures Undercoat - Solvent-borne
- ASTM D1050-05(2022) Standard Specification for Rubber Insulating Line Hose
- ASTM D1053-92a(2018) Standard Test Methods for Rubber Property—Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics
- ASTM D1056-20 Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber
- ASTM D1059-17(2022) Standard Test Method for Yarn Number Based on Short-Length Specimens
- ASTM D1062-08(2023) Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
- ASTM D1065-18(2022) Standard Test Method for Unsaponifiable Matter in Pine Chemicals, Including Rosin, Tall Oil, and Related Products
- ASTM D1067-16 Standard Test Methods for Acidity or Alkalinity of Water