
【国外标准】 Standard Specification for Joint Sealants, Hot Applied, Jet Fuel Resistant Types, for Portland Cement Concrete Pavements
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers joint and crack sealants of the hot applied, jet fuel resistant type intended for use in sealing joints and cracks in Portland cement concrete in areas that are subject to fuel spillage. Three types of joint sealants are presented: type I - joint sealant which is resilient and capable of maintaining an effective seal in hot to moderate climates, type II - joint sealant capable of maintaining an effective seal in hot to moderate climates, and type III - joint sealant capable of maintaining an effective seal in most climates experiencing moderate to cold temperatures. The specimen conditioning, cone penetration, aged cone penetration retention, and softening point shall be tested to meet the requirements prescribed. Non-immersed bond, water immersed bond, fuel immersed bond, resilience, and oven aged resilience shall be tested to meet the requirements prescribed. The tensile adhesion, artificial weathering, and flexibility of the sealant shall be tested to meet the requirements prescribed.1.1 This specification covers joint and crack sealants of the hot-applied type intended for use in sealing joints and cracks in portland cement concrete in areas that are subject to fuel spillage.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D7116-16(2021)
标准名称:
Standard Specification for Joint Sealants, Hot Applied, Jet Fuel Resistant Types, for Portland Cement Concrete Pavements
英文名称:
Standard Specification for Joint Sealants, Hot Applied, Jet Fuel Resistant Types, for Portland Cement Concrete Pavements标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D2561-17(2023) Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
- ASTM D2574-16(2020)e1 Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms
- ASTM D2578-23 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
- ASTM D2582-21 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
- ASTM D2591-07(2020) Standard Test Method for Linear Density of Elastomeric Yarns (Short Length Specimens)
- ASTM D2593-23 Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography
- ASTM D2596-20 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
- ASTM D2598-21 Standard Practice for Calculation of Certain Physical Properties of Liquefied Petroleum (LP) Gases from Compositional Analysis
- ASTM D2616-19 Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale
- ASTM D2619-21 Standard Test Method for Hydrolytic Stability of Hydraulic Fluids (Beverage Bottle Method)
- ASTM D2621-87(2016) Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints
- ASTM D2624-22 Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
- ASTM D263-05(2023) Standard Specification for Chrome Oxide Green Pigment
- ASTM D2633-21 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
- ASTM D2639/D2639M-23 Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer