
【国外标准】 Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 The purpose of this test method is to provide data on liquid drop-size characteristics for sprays, as indicated by optical nonimaging light-scattering instruments. The results obtained generally will be statistical in nature. The number of variables concerned in the production of liquid spray, together with the variety of optical, electronic, and sampling systems used in different instruments, may contribute to variations in the test results. Care must be exercised, therefore, when attempting to compare data from samples obtained by different means.1.1 The purpose of this test method is to obtain data which characterize the sizes of liquid particles or drops such as are produced by a spray nozzle or similar device under specified conditions using a specified liquid. The drops will generally be in the size range from 5-μm to the order of 1 000-μm diameter; they will occur in sprays which may be as small as a few cubic centimetres or as large as several cubic metres. Typically the number density of the particles can vary significantly from one point to another.1.2 This test method is intended primarily for use in standardizing measurements of the performance of sprayproducing devices. It is limited to those techniques and instruments that operate by passing a beam of light through the spray and analyzing the light scattered by the droplets to derive size information. Such techniques do not produce images of individual drops, and therefore, are known as “optical (nonimaging) instruments.”1.3 The measurements made, when referred to the entire spray being sampled, may be flux sensitive or spatial, as defined in Practice E799, depending on the techniques used with a particular instrument.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E1260-03(2020)
标准名称:
Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments
英文名称:
Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D6099-18 Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Moderate to High Acidity Aromatic Isocyanates
- ASTM D610-08(2019) Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
- ASTM D6100-17 Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
- ASTM D6104-97(2017)e1 Standard Practice for Determining the Performance of Oil/Water Separators Subjected to Surface Run-Off
- ASTM D6105-04(2019) Standard Practice for Application of Electrical Discharge Surface Treatment (Activation) of Plastics for Adhesive Bonding
- ASTM D6107-97(2023) Standard Specification for Stop-Leak Additive for Engine Coolants Used in Light Duty Service
- ASTM D6108-19 Standard Test Method for Compressive Properties of Plastic Lumber and Shapes
- ASTM D611-23 Standard Test Methods for Aniline Point and Mixed Aniline Point of Petroleum Products and Hydrocarbon Solvents
- ASTM D6111-19a Standard Test Method for Bulk Density And Specific Gravity of Plastic Lumber and Shapes by Displacement
- ASTM D6112-23 Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes
- ASTM D6117-23 Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes
- ASTM D6119-19(2024) Standard Practice for Creating Surface Appearance Changes in Pile Yarn Floor Covering from Foot Traffic
- ASTM D6122-23 Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
- ASTM D6123/D6123M-97(2020) Standard Specification for Pressure-Sensitive Tape for Light-Duty Packaging and General Purpose Masking
- ASTM D6124-06(2022) Standard Test Method for Residual Powder on Medical Gloves