
【国外标准】 Standard Specification for Melamine-Formaldehyde Molding Compounds
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers compression molding, thermosetting, melamine-formaldehyde molding compounds, resin binder, with or without other resins, intimately combined with fillers, pigments, and any chemical agents needed. The molding compounds shall conform to the requirements specified. Tests shall be performed to determine the properties of the material in accordance with the following test methods: bulk factor; specific gravity; water absorption; impact resistance; flexural strength; deflection temperature; dielectric strength; permittivity and dissipation factor; arc resistance; shrinkage; and comparative tracking index.1.1 This specification covers compression molding, thermosetting, melamine-formaldehyde molding compounds as further defined in 4.1, resin binder, with or without other resins, intimately combined with fillers, pigments, and any chemical agents needed.1.2 The values stated in SI units are to be regarded as the standard.NOTE 1: The properties included in this specification are those required to identify the types of molding compounds covered. There may be other requirements necessary to identify particular characteristics. These will be added to the specification as their inclusion becomes generally desirable and the necessary test data and methods become available. Transfer or injection molding will usually result in different physical and electrical characteristics than compression molding.NOTE 2: ISO 2122-1977(E) is similar but not equivalent to this specification. Product classification and characterization are not equivalent.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D704-99(2020)
标准名称:
Standard Specification for Melamine-Formaldehyde Molding Compounds
英文名称:
Standard Specification for Melamine-Formaldehyde Molding Compounds标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D7039-15a(2020) Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
- 下一篇: ASTM D7040-04(2020) Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
- 推荐标准
- ASTM D2561-17(2023) Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
- ASTM D2574-16(2020)e1 Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms
- ASTM D2578-23 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
- ASTM D2582-21 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
- ASTM D2591-07(2020) Standard Test Method for Linear Density of Elastomeric Yarns (Short Length Specimens)
- ASTM D2593-23 Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography
- ASTM D2596-20 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
- ASTM D2598-21 Standard Practice for Calculation of Certain Physical Properties of Liquefied Petroleum (LP) Gases from Compositional Analysis
- ASTM D2616-19 Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale
- ASTM D2619-21 Standard Test Method for Hydrolytic Stability of Hydraulic Fluids (Beverage Bottle Method)
- ASTM D2621-87(2016) Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints
- ASTM D2624-22 Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
- ASTM D263-05(2023) Standard Specification for Chrome Oxide Green Pigment
- ASTM D2633-21 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
- ASTM D2639/D2639M-23 Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer