
【国外标准】 Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester. Each type of thermoplastic polyester shape may be categorized into one of several grades as follows: grade 1 - general purpose-extruded or compression molded product made using only 100 % virgin thermoplastic polyester resin and grade 2 - recycled-extruded or compression molded product made using any amount up to 100 % recycled thermoplastic polyester plastics. Tensile stress break, elongation at break, and tensile modulus shall be tested to meet the requirements prescribed.1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic polyester.1.2 The properties included in this specification are those required for the compositions covered. Use the classification system given in Section 4 to describe requirements necessary to identify particular characteristics important to specialized applications.1.3 This specification allows the use of recycled plastics2 (see Section 4).1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 and Table S-TPES only.1.5 The following precautionary caveat pertains only to the test method portions sections of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: There is no known ISO equivalent to this standard.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6261-14(2022)
标准名称:
Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
英文名称:
Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM C117-23 Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
- ASTM C1170/C1170M-20 Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
- ASTM C1173-22 Standard Specification for Flexible Transition Couplings for Underground Piping Systems
- ASTM C1174-20 Standard Guide for Evaluation of Long-Term Behavior of Materials Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste
- ASTM C1177/C1177M-17 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
- ASTM C1178/C1178M-18 Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel
- ASTM C1181/C1181M-17 Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts
- ASTM C1184-23 Standard Specification for Structural Silicone Sealants
- ASTM C1185-23 Standard Test Methods for Sampling and Testing Fiber-Cement Flat Sheet, Roofing and Siding Shingles, and Clapboards
- ASTM C1186-22e1 Standard Specification for Flat Fiber-Cement Sheets
- ASTM C1190-18(2022) Standard Practice for Location of Test Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick
- ASTM C1193-16(2023) Standard Guide for Use of Joint Sealants
- ASTM C1195-21 Standard Test Method for Absorption of Architectural Cast Stone
- ASTM C1196-20 Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements
- ASTM C12-22a Standard Practice for Installing Vitrified Clay Pipe Lines