
【国外标准】 Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 Leakage of gas or liquid from a pressurized system, whether through a crack, orifice, seal break, or other opening, may involve turbulent or cavitational flow, which generates acoustic energy in both the external atmosphere and the system pressure boundary. Acoustic energy transmitted through the pressure boundary can be detected at a distance by using a suitable acoustic emission sensor.4.2 With proper selection of frequency passband, sensitivity to leak signals can be maximized by eliminating background noise. At low frequencies, generally below 100 kHz, it is possible for a leak to excite mechanical resonances within the structure that may enhance the acoustic signals used to detect leakage.4.3 This practice is not intended to provide a quantitative measure of leak rates.1.1 This practice describes a passive method for detecting and locating the steady state source of gas and liquid leaking out of a pressurized system. The method employs surface-mounted acoustic emission sensors (for non-contact sensors see Test Method E1002), or sensors attached to the system via acoustic waveguides (for additional information, see Terminology E1316), and may be used for continuous in-service monitoring and hydrotest monitoring of piping and pressure vessel systems. High sensitivities may be achieved, although the values obtainable depend on sensor spacing, background noise level, system pressure, and type of leak.1.2 Units—The values stated in either SI units or inch-pound units are to be regarded as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standards.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E1211/E1211M-17
标准名称:
Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors
英文名称:
Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D5793-18(2022) Standard Test Method for Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings
- ASTM D5794-95(2021) Standard Guide for Determination of Anions in Cathodic Electrocoat Permeates by Ion Chromatography
- ASTM D5798-21 Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines
- ASTM D5800-21 Standard Test Method for Evaporation Loss of Lubricating Oils by the Noack Method
- ASTM D5801-24 Standard Test Method for Toughness and Tenacity of Asphalt Materials
- ASTM D5805-00(2023) Standard Test Methods for Rubber—Determination of Carbon Black in Masterbatches
- ASTM D5806-95(2017) Standard Test Method for Disinfectant Quaternary Ammonium Salts by Potentiometric Titration
- ASTM D5807-18 Standard Practice for Evaluating the Overpressurization Characteristics of Inflatable Restraint Cushions
- ASTM D5810-96(2021) Standard Guide for Spiking into Aqueous Samples
- ASTM D5811-20 Standard Test Method for Strontium-90 in Water
- ASTM D5814-23 Standard Practice for Determination of Contamination in Recycled Poly(Ethylene Terephthalate) (PET) Flakes and Chips Using a Plaque Test
- ASTM D5817-20 Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing
- ASTM D5821-13(2017) Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
- ASTM D5822-13(2019) Standard Test Method for Determining Seam Strength in Inflatable Restraint Cushions
- ASTM D5823-19(2024) Standard Test Method for Tuft Height of Pile Floor Coverings