
【国外标准】 Standard Practice for Determination of Total and Available Cyanide in Solid Waste and Soil after Alkaline Extraction
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Cyanide and hydrogen cyanide are highly toxic. Regulations have been established requiring the measurement of cyanide in soil and solid waste samples. This practice is also useful for performing material balances to account for the distribution of cyanides in cyanidation products from metallurgical processes.5.2 This practice is applicable to the determination of available or total water soluble, or both, and water insoluble cyanides in soil and solid waste.5.3 Water insoluble cyanide complexes, such as Prussian blue, are not completely recovered by distillation methods. This practice extracts all cyanides, including the water insoluble cyanides such as Prussian blue, and then the extract solution can be analyzed for cyanide with Test Methods D6888, D7284, or D7511.1.1 This practice is used for the determination of total or available cyanide in solid waste, sediment and soil samples after alkaline extraction. Simple cyanide (CN-) salts of group 1 and group 2 (alkali and alkaline earth) metals; soluble alkali and alkaline earth salts of zinc, copper, cadmium, mercury, nickel, silver, and iron cyanide complexes; and insoluble metal-metal cyanide complexes, such as Prussian blue, are quantitatively recovered. Gold, platinum group metals and cobalt cyanide complexes are not recovered during analysis.1.2 Free cyanide cannot be determined due to the change of equilibrium conditions during the extraction process.1.3 Cyanide complexes are extracted into an alkaline solution as described in this practice. Measure the total cyanide using Test Methods D7511 or D7284. Measure the available cyanide using Test Method D6888. Calculate cyanide content in the soil or waste.1.4 The method detection limit (MDL) is dependent on the test method used to measure the cyanide content. Based on the methods cited, it is approximately 1 mg/kg and the minimum level (ML) is 5 mg/kg. The applicable range is also dependent on the test method used to measure cyanide. Based on the methods cited, it is 5 to 100 mg/kg.1.5 This practice should be used by analysts experienced with extractions and flow injection analysis (FIA), or working under the close supervision of such qualified persons.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 9.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8273-20
标准名称:
Standard Practice for Determination of Total and Available Cyanide in Solid Waste and Soil after Alkaline Extraction
英文名称:
Standard Practice for Determination of Total and Available Cyanide in Solid Waste and Soil after Alkaline Extraction标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D8272-19 Standard Guide for Development and Optimization of D19 Chemical Analysis Methods Intended for EPA Compliance Reporting
- 下一篇: ASTM D8274-20a Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil by Portable Rapid Mid-Infrared Analyzer
- 推荐标准
- ASTM E3168-20a Standard Practice for Determining Low-Contrast Visual Acuity of Radiographic Interpreters
- ASTM E317-21 Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments
- ASTM E3170/E3170M-18(2023) Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints
- ASTM E3171-21a Standard Test Method for Determination of Total Silver in Textiles by ICP-OES or ICP-MS Analysis
- ASTM E3178-18 Standard Practice for Evaluating Static and Cidal Chemical Decontaminants against Bacillus Spores using Centrifugal Filtration Tubes
- ASTM E3182-20 Standard Practice for Preparing an Occupant Exposure Screening Report (OESR) for Substances in Installed Building Products
- ASTM E3186-19 Standard Guide for Use and Testing of Dry-Block Temperature Calibrators
- ASTM E3191-18 Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination
- ASTM E3192/E3192M-20 Standard Practice for Soft Armor Conditioning by Tumbling
- ASTM E3197-23 Standard Terminology Relating to Examination of Fire Debris
- ASTM E3199-22a Standard Guide for Alternative Allocation Approaches to Modeling Input and Output Flows of Secondary Materials and Related Recycling Scenarios in Life Cycle Assessment
- ASTM E3200-21 Standard Guide for Investment Analysis in Environmentally Sustainable Manufacturing
- ASTM E3208-20 Standard Specification for Minimum Equipment Requirements for Mobile Surface Contaminant Classification and Measurement Equipment
- ASTM E3209/E3209M-20 Standard Test Method for Pavement Thickness by Magnetic Pulse Induction
- ASTM E321-20 Standard Test Method for Atom Percent Fission in Uranium and Plutonium Fuel (Neodymium-148 Method)