
【国外标准】 Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method was developed to provide for the enforcement of 26 CFR 48.4082-1(b), which mandates that all tax-exempt diesel fuels be dyed with an amount of Solvent Red 164 at a concentration that is spectrally equivalent to 3.9 lb/103 bbl (11.1 mg/L) of Solvent Red 26. It is employed to verify that the correct amount of Solvent Red 164 is being added to tax-exempt product at terminals or refineries prior to sale, and to detect the presence of Solvent Red 164 in taxed product intended for on-road use.5.1.1 Solvent Red 26 is the azo dye shown in Fig. 1. It is the standard against which the concentration of Solvent Red 164 is measured because it is available in a certified pure form. Solvent Red 164 is identical in structure to Solvent Red 26 except that it has hydrocarbon (alkyl) chains incorporated to increase its solubility in diesel and burner fuels. The exact composition of Solvent Red 164 will vary from manufacturer to manufacturer and lot to lot depending upon the extent of alkylation that occurs during production; however, its visible spectrum is virtually identical to the spectrum of Solvent Red 26. Solvent Red 164 is employed in the field (instead of Solvent Red 26) to dye tax-exempt diesel and burner fuels because of its higher solubility and relatively low cost.FIG. 1 Structure of Solvent Red 261.1 This test method covers the procedure for determining the concentration of dye Solvent Red 164 in commercially available diesel and burner fuels using visible spectroscopy.NOTE 1: This test method is suitable for all No. 1 and No. 2 grades in Specifications D396 and D975 and for grades DMA and DMB in Specification D2069.1.2 The concentration ranges specified for the calibration standards are established in response to the Internal Revenue Service dyeing requirements which state that tax-exempt diesel fuel satisfies the dyeing requirement only if it contains the dye Solvent Red 164 (and no other dye) at a concentration spectrally equivalent to 3.9 lb of the solid dye standard Solvent Red 26 per thousand bbl (11.1 mg/L) of diesel fuel.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6258-17
标准名称:
Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels
英文名称:
Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D5404/D5404M-21 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator
- ASTM D5405/D5405M-98(2021) Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material
- ASTM D5406-22 Standard Practice for Rubber—Calculation of Producer's Process Performance Indexes
- ASTM D5412-93(2017)e1 Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- ASTM D5413-21 Standard Test Methods for Measurement of Water Levels in Open-Water Bodies
- ASTM D5414-95(2020) Standard Test Method for Evaluation of Horizontal Impact Performance of Load Unitizing Stretch Wrap Films
- ASTM D5416-95(2020) Standard Test Method for Evaluating Abrasion Resistance of Stretch Wrap Films by Vibration Testing
- ASTM D542-22 Standard Test Method for Index of Refraction of Transparent Organic Plastics
- ASTM D5420-21 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
- ASTM D5422-17 Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer
- ASTM D5424-23a Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
- ASTM D5425-23 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products
- ASTM D5426-19 Standard Practices for Visual Inspection and Grading of Fabrics Used for Inflatable Restraints
- ASTM D5427-09(2019) Standard Practice for Accelerated Aging of Inflatable Restraint Fabrics
- ASTM D5428-08(2019) Standard Practice for Evaluating the Performance of Inflatable Restraint Modules