
【国外标准】 Standard Test Method for Evaluation of Recoverable Stretch of Stretch Yarns (Skein Method)
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between-laboratory precision are acceptable and the method is used extensively in the trade for acceptance testing.5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use samples for such comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing, and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.5.2 This test differs from other crimp contraction test methods in that it measures the recoverable stretch during the unload cycle of the yarn.1.1 This test method covers the determination of the recoverable stretch of commercial textured yarns, covered elastomeric yarns and other stretch yarns using skeins. This test method is particularly valuable for yarns that develop additional crimp upon exposure to hot, wet conditions. The recoverable stretch is a relative measure of the recovery power the yarn can be expected to provide in a finished fabric.1.2 This test method is applicable to continuous filament yarns and is suitable for yarns that develop additional stretch potential upon exposure to heat.1.3 This method is applicable to yarns 500 denier or finer.1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6720-07(2018)
标准名称:
Standard Test Method for Evaluation of Recoverable Stretch of Stretch Yarns (Skein Method)
英文名称:
Standard Test Method for Evaluation of Recoverable Stretch of Stretch Yarns (Skein Method)标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4713-12(2020) Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
- ASTM D4716/D4716M-22 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
- ASTM D4718/D4718M-15(2023) Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
- ASTM D4724/D4724M-21 Standard Test Method for Entanglements in Filament Yarns by Needle Insertion
- ASTM D4727/D4727M-22 Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes
- ASTM D4728-17(2022) Standard Test Method for Random Vibration Testing of Shipping Containers
- ASTM D4734-20 Standard Specification for Refined Benzene-545
- ASTM D4740-20 Standard Test Method for Cleanliness and Compatibility of Residual Fuels by Spot Test
- ASTM D4748-10(2020) Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar
- ASTM D476-15(2021) Standard Classification for Dry Pigmentary Titanium Dioxide Products
- ASTM D4761-19 Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials
- ASTM D4762-23 Standard Guide for Testing Polymer Matrix Composite Materials
- ASTM D4763-06(2020) Standard Practice for Identification of Chemicals in Water by Fluorescence Spectroscopy
- ASTM D4764-01(2023) Standard Test Method for Determination by X-ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint
- ASTM D4765-13(2018) Standard Test Method for Measurement of Fluorides in Workplace Atmospheres by Ion-Selective Electrodes