
【国外标准】 Standard Specification for Pressure-Sensitive Tape for Packaging, Filament-Reinforced
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
10.1 The pressure-sensitive, filament-reinforced tapes covered by this specification are intended for use in closing and reinforcing fiberboard boxes and for bundling items for shipment.10.2 Type I is an impact and cut-resistant low-tensile strength tape, usually with polyester fiber reinforcement. It is intended for bundling and similar applications and used where a greater amount of stretch before break provides an improvement in impact resistance over glass filament reinforcement.10.3 Types II and III are intended for reinforcement of RSC's and similar fiberboard boxes, and for bundling where a snug bundle must be maintained and other similar applications.10.4 Type IV is intended for applications in which weather-resistance high-tensile strength tape is required.10.5 See Practice D1974/D1974M for details on applications.AbstractThis specification covers filament-reinforced, pressure-sensitive adhesive tape for packaging and includes the following types: Type I, Type II, Type III, and Type IV. The tapes covered by this specification are intended for use in closing and reinforcing fiberboard boxes and for bundling items for shipment. The materials used in the construction of the tapes shall be such that they ensure performance of the tape over the prescribed temperature range. The material and manufacture requirements for backing, adhesive, reinforcements, and rolls are specified. The tape shall comply with the physical property requirements such as (1) adhesion before and after aging, (1) adhesion at low temperature, (3) elongation, (4) shear adhesion, (5) break strength, and (6) thickness. Additional physical requirements are specified for Type IV tape. The tape shall meet the prescribed dimension (including the roll width, roll length, and splice overlap), color, and transparency requirements. The sampling method for end-item examination and end-item testing are given. Accelerated aging (heat and humidity), adhesion, break strength and elongation, thickness, and weathering (for Type IV only) tests shall be performed. Environmental considerations such as toxic content are also specified.1.1 This specification covers filament-reinforced, pressure-sensitive adhesive tape.1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system must be used independently of the other, without combining values in any way.1.3 The following precautionary caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D5330/D5330M-06(2020)
标准名称:
Standard Specification for Pressure-Sensitive Tape for Packaging, Filament-Reinforced
英文名称:
Standard Specification for Pressure-Sensitive Tape for Packaging, Filament-Reinforced标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 推荐标准
- ASTM D3815/D3815M-05(2019) Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
- ASTM D3816/D3816M-96(2020) Standard Test Method for Water Penetration Rate of Pressure-Sensitive Tapes
- ASTM D3822/D3822M-14(2020) Standard Test Method for Tensile Properties of Single Textile Fibers
- ASTM D3824-20 Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by Chemiluminescence
- ASTM D3829-20a Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil
- ASTM D3831-22 Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy
- ASTM D3836-13(2021) Standard Practice for Evaluation of Automotive Polish
- ASTM D3838-23 Standard Test Method for pH of Activated Carbon
- ASTM D3843-16(2021)e1 Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
- ASTM D3849-22 Standard Test Method for Carbon Black—Morphological Characterization of Carbon Black Using Electron Microscopy
- ASTM D3850-19 Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA)
- ASTM D3852-20 Standard Practice for Sampling and Handling Phenol, Cresols, and Cresylic Acid
- ASTM D3859-15(2023) Standard Test Methods for Selenium in Water
- ASTM D3861-22 Standard Test Method for Quantity of Water-Extractable Matter in Membrane Filters
- ASTM D3864-12(2021) Standard Guide for On-Line Monitoring Systems for Water Analysis