
【国外标准】 Standard Specification for Polyethylene Upright Storage Tanks
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. This specification does not cover the design of vessels intended for use at pressures other than atmospheric pressure. Furthermore, this specification does not cover the design of portable tanks and is not for vessels intended for use with liquids heated above their flash points in continuous service. Special design considerations not covered in this specification shall be given to vessels subject to superimposed mechanical forces, such as seismic forces, wind load or agitation; to vessels subject to service above specified temperature; and vessels subject to specified superimposed pressure of water. Low-temperature impact test shall be performed on rotational-molded polyethylene tanks. The test method is used on tanks molded from both the crosslinked and non-crosslinked polyethylenes. Dart drop impact test shall be performed to determine the quality of the tank. O-xylene-insoluble fraction or gel test shall be performed on crosslinked polyethylene. Visual inspection and water test shall also be performed on the samples.1.1 This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship and appearance. Tank capacities are from 1900 L (500 gal) up.1.2 This specification covers the design of stationery vessels for use at atmospheric pressure intended for use with liquids heated below their flash points and continuous service temperatures below 66°C (150°F) for Type I tanks and below 60°C (140°F) for Type II tanks.1.2.1 NFPA Standards 30 and NFPA 31 shall be consulted for installations that are subject to the requirements of these standards.1.3 For service requirements beyond the scope of this specification (1.2), such as externally imposed mechanical forces, internal pressure or vacuum, higher temperature service, etc., other relevant sources of standards, for example, local and state building codes, NFPA, ASME, ARM, etc., shall be consulted.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.NOTE 1: ISO 13341:2005+A1:2011 and ISO 13575:2012 are similar, but not equivalent to this standard.1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D1998-21
标准名称:
Standard Specification for Polyethylene Upright Storage Tanks
英文名称:
Standard Specification for Polyethylene Upright Storage Tanks标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D2561-17(2023) Standard Test Method for Environmental Stress-Crack Resistance of Blow-Molded Polyethylene Containers
- ASTM D2574-16(2020)e1 Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms
- ASTM D2578-23 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
- ASTM D2582-21 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
- ASTM D2591-07(2020) Standard Test Method for Linear Density of Elastomeric Yarns (Short Length Specimens)
- ASTM D2593-23 Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography
- ASTM D2596-20 Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
- ASTM D2598-21 Standard Practice for Calculation of Certain Physical Properties of Liquefied Petroleum (LP) Gases from Compositional Analysis
- ASTM D2616-19 Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale
- ASTM D2619-21 Standard Test Method for Hydrolytic Stability of Hydraulic Fluids (Beverage Bottle Method)
- ASTM D2621-87(2016) Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints
- ASTM D2624-22 Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
- ASTM D263-05(2023) Standard Specification for Chrome Oxide Green Pigment
- ASTM D2633-21 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
- ASTM D2639/D2639M-23 Standard Test Method for Plastic Properties of Coal by the Constant-Torque Gieseler Plastometer