【国外标准】 Standard Practice for Finite Element Analysis (FEA) of Metallic Orthopaedic Total Knee Tibial Components
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
3.1 This practice is applicable to the calculation of stresses seen on a knee tibial component when loaded in a manner described in this practice. This practice can be used to identify the worst-case size for a particular implant. When stresses calculated using this FEA method were compared to the stresses measured at two locations on the tibial tray using physical strain gauging techniques performed at one laboratory, the difference observed was -6.8 % at one location (with the strain gauges reporting the higher stress) and 3.1 % at the other location (with the FEA method reporting a higher stress). This difference should be considered when determining the worst-case size(s) of the same implant design.3.2 The loading of tibial tray designs in vivo will, in general, differ from the loading defined in this practice. However, this practice is designed to allow for comparisons between the fatigue performance of different metallic tibial component designs, when tested under similar conditions.1.1 This practice establishes requirements and considerations for the numerical simulation of metallic orthopaedic total knee tibial components using Finite Element Analysis (FEA) techniques for the estimation of stresses and strains. This practice is only applicable to stresses below the yield strength, as provided in the material certification.1.2 Purpose—This practice establishes requirements and considerations for the development of finite element models to be used in the evaluation of metallic orthopaedic total knee tibial component designs for the purpose of prediction of the static implant stresses and strains. This procedure can be used for worst-case assessment within a series of different implant sizes of the same implant design to reduce the physical test burden. Recommended procedures for performing model checks and verification are provided as an aid to determine if the analysis follows recommended guidelines. Finally, the recommended content of an engineering report covering the mechanical simulation is presented.1.3 Limits—This practice is limited in discussion to the static structural analysis of metallic orthopaedic total knee tibial components (which excludes the prediction of fatigue strength).1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F3334-19
标准名称:
Standard Practice for Finite Element Analysis (FEA) of Metallic Orthopaedic Total Knee Tibial Components
英文名称:
Standard Practice for Finite Element Analysis (FEA) of Metallic Orthopaedic Total Knee Tibial Components标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM F3333-20 Standard Specification for Chopped Carbon Fiber Reinforced (CFR) Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications
- 下一篇: ASTM F3335-20 Standard Guide for Assessing the Removal of Additive Manufacturing Residues in Medical Devices Fabricated by Powder Bed Fusion
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-082-02:2024 Fibre optic interconnecting devices and passive components. Performance standard
- BS ISO 5501-2:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-3:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-1:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- KS D ISO 9226 금속 및 합금의 부식-대기의 부식성-부식성 평가를 위한 표준 시험편의 부식 속도 결정
- KS B 0831 비파괴검사 — 초음파탐상검사 — 표준 시험편
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication