【国外标准】 Standard Specification for PTFE Resin Skived Tape
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
This specification covers four types and two grades of skived tapes in specified thicknesses manufactured by skiving from PTFE resin molding and extrusion materials. The four types covered here are: Type I (premium), normally used for exacting electrical, mechanical, or chemical applications; Type II (general purpose), for electrical, mechanical, and chemical applications not requiring premium material; Type III (commercial), for non-critical chemical, electrical, and mechanical applications; and Type IV (utility), having no electrical requirements, and with mechanical properties at lower level. Subsequently, all four types may be subdivided into Grade 1, which is made only from virgin resin, and Grade 2, which may be made using reprocessed resin, or a mixture of virgin and reprocessed resin. Appropriately sampled specimens shall be tested and conform accordingly to the following physical requirements: dimension (length, width, and thickness); melting point; tensile properties (tensile strength and elongation at break); specific gravity; dielectric strength; and non-dielectric strength failure mode electrical flaws.1.1 This specification covers skived tape in thicknesses from 0.013 to 6.35 mm (0.0005 to 0.250 in.) manufactured by skiving (Note 1) from PTFE resin molding and extrusion materials.NOTE 1: Skiving is the process of continuously shaving a film on a lathe from the outer surface to the core of a molded cylindrical tube of material.NOTE 2: Abbreviations have been approved from Terminology D1600.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.1.3 The following hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 3: This specification and ISO 13000-1 and ISO 13000-2 differ in approach or detail, and data obtained using either may not be technically equivalent.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D3308-12(2022)
标准名称:
Standard Specification for PTFE Resin Skived Tape
英文名称:
Standard Specification for PTFE Resin Skived Tape标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS ISO 5501-2:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-3:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-1:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- KS D ISO 9226 금속 및 합금의 부식-대기의 부식성-부식성 평가를 위한 표준 시험편의 부식 속도 결정
- KS B 0831 비파괴검사 — 초음파탐상검사 — 표준 시험편
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard