【国外标准】 Standard Test Method for Yarn Number Based on Short-Length Specimens
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 This is a quick method used for the determination of the approximate yarn number of short-length specimens taken from packages or fabrics.5.2 Because any error present in the reported length of the specimen is multiplied many times when calculating the theoretical yarn number using Eq 2 or Eq 3, it is extremely important that the length be measured as precisely as practicable.5.3 For the analysis of fabrics, this test method is adequate for estimating the approximate yarn number of the yarn used to weave or knit the fabric, but the results obtained by this test method may not agree with the nominal yarn number of the yarns actually used to make the fabric because of the changes in the yarn number produced by the weaving or knitting operations, the finishing treatments, and the dissecting operations. This test method is suitable for the evaluation of yarns as they occur in the finished fabric, when that information is needed.5.4 The yarn number obtained from the lengths taken from packages should not be expected to agree exactly with the values obtained by the use of the more precise methods of determining the yarn number included in Test Method D1907. If a sufficient number of consecutive specimens were tested, however, a close agreement with Option 1 of Test Method D1907 can be expected.5.5 This test method is designed to measure the yarn number of the single yarns present as a component of a plied yarn and the yarn number of the original single yarns used to produce a high twist yarn for a crepe fabric.5.6 This test method is not recommended for acceptance testing because of the short lengths used. In some cases, the purchaser and the supplier may have to test a commercial shipment of one or more specific materials by the best available method, even though the method has not been recommended for acceptance testing of commercial shipments.5.6.1 In such a case, if there is disagreement arising from the differences in values reported by the purchaser and supplier when using this method for acceptance testing, the statistical bias, if any, between the laboratory of the purchaser and the laboratory of the supplier should be determined with each comparison being based on testing specimens randomly drawn from one sample of material of the type being evaluated.1.1 This test method covers the determination of the yarn number of all types of cotton, woolen, worsted, and man-made fiber yarns taken from packages; or from any textile fabrics in which the yarns are intact and can be removed in measurable lengths. The test method is not applicable to yarns taken from napped or cut pile fabrics. Because this test method is based on short-length specimens, the results should only be considered as approximations of yarn number.NOTE 1: For a more precise procedure for the determination of yarn number, refer to Test Method D1907.NOTE 2: The following additional methods for the determination of yarn number have been approved for yarns made from specific fibers: Specification D541, D578, and D681.1.2 This test method is applicable to yarns which stretch less than 5 % when tension on yarn is increased from 0.25 to 0.75 cN/tex (0.25 to 0.75 gf/tex). By mutual agreement it may be adapted to yarns which stretch more than 5 % by use of tension lower than that specified in the method for elastomers or use of tension higher than that specified in the method to pull the crimp out of textured yarns.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D1059-17(2022)
标准名称:
Standard Test Method for Yarn Number Based on Short-Length Specimens
英文名称:
Standard Test Method for Yarn Number Based on Short-Length Specimens标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard
- BS EN 14662-1:2023 - TC Tracked Changes. Ambient air quality. Standard method for measurement of benzene concentrations