
【国外标准】 Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers four types of joint and crack sealants of the hot applied type intended for use in sealing joints and cracks in Portland cement concrete and asphaltic concrete pavements. However, this specification does not address the properties required of sealants for use in areas of Portland cement concrete or asphaltic pavement that are subject to jet fuel or other fuel spillage such as vehicle and/or aircraft refuel and maintenance areas. The sealants shall be sampled and tested appropriately to examine their conformance with specified values of the following requirements: cone penetration; softening point; non-immersed and water-immersed bond properties; oven aged resilience; and asphalt compability.1.1 This specification covers joint and crack sealants of the hot-applied type intended for use in sealing joints and cracks in portland cement concrete and asphaltic concrete pavements.1.2 This specification does not purport to cover the properties required of sealants for use in areas of portland cement concrete or asphaltic pavement subject to jet fuel or other fuel spillage such as vehicle and/or aircraft refuel and maintenance areas.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6690-21
标准名称:
Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements
英文名称:
Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D669-03 Standard Test Method for Dissipation Factor and Permittivity Parallel with Laminations of Laminated Sheet and Plate Materials (Withdrawn 2012)
- 下一篇: ASTM D6691-17 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum
- 推荐标准
- ASTM D5793-18(2022) Standard Test Method for Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings
- ASTM D5794-95(2021) Standard Guide for Determination of Anions in Cathodic Electrocoat Permeates by Ion Chromatography
- ASTM D5798-21 Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines
- ASTM D5800-21 Standard Test Method for Evaporation Loss of Lubricating Oils by the Noack Method
- ASTM D5801-24 Standard Test Method for Toughness and Tenacity of Asphalt Materials
- ASTM D5805-00(2023) Standard Test Methods for Rubber—Determination of Carbon Black in Masterbatches
- ASTM D5806-95(2017) Standard Test Method for Disinfectant Quaternary Ammonium Salts by Potentiometric Titration
- ASTM D5807-18 Standard Practice for Evaluating the Overpressurization Characteristics of Inflatable Restraint Cushions
- ASTM D5810-96(2021) Standard Guide for Spiking into Aqueous Samples
- ASTM D5811-20 Standard Test Method for Strontium-90 in Water
- ASTM D5814-23 Standard Practice for Determination of Contamination in Recycled Poly(Ethylene Terephthalate) (PET) Flakes and Chips Using a Plaque Test
- ASTM D5817-20 Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing
- ASTM D5821-13(2017) Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
- ASTM D5822-13(2019) Standard Test Method for Determining Seam Strength in Inflatable Restraint Cushions
- ASTM D5823-19(2024) Standard Test Method for Tuft Height of Pile Floor Coverings