
【国外标准】 Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method is a tool for quality assurance use. Given a pressure-sensitive label stock and a requirement in terms of the minimum or maximum peel adhesion value expected for this label stock, the data from the test can be used in conjunction with acceptance criteria.5.2 This test method can show the relative bond strength of a given label stock to one or more surfaces of varied material and texture as compared to the standard stainless steel panel. Substitution of panels representative of the proposed substrates for the standard stainless steel panel would be acceptable for this procedure.1.1 This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks. This test method gives a measure of the adherence to a standard steel substrate or to other surfaces of interest for a pressure-sensitive label stock.1.2 This test method provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive label stock. The assessment may be within a sheet or roll, between sheets or rolls, or between production lots.1.3 Variations in the label stock facestock and adhesive can affect the response; therefore, this test method cannot be used to pinpoint the specific cause(s) of nonuniformity.1.4 This test method may not be appropriate to test label stocks having either stiff backings or backings showing a high stretch at low forces. These characteristics could result in a high variability of the test response, which is not a true indication of the real nature of the adhesive bond.1.5 The values stated in either SI or inch-pound units are to be regarded separately as the standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6252/D6252M-98(2019)
标准名称:
Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
英文名称:
Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D5404/D5404M-21 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator
- ASTM D5405/D5405M-98(2021) Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material
- ASTM D5406-22 Standard Practice for Rubber—Calculation of Producer's Process Performance Indexes
- ASTM D5412-93(2017)e1 Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- ASTM D5413-21 Standard Test Methods for Measurement of Water Levels in Open-Water Bodies
- ASTM D5414-95(2020) Standard Test Method for Evaluation of Horizontal Impact Performance of Load Unitizing Stretch Wrap Films
- ASTM D5416-95(2020) Standard Test Method for Evaluating Abrasion Resistance of Stretch Wrap Films by Vibration Testing
- ASTM D542-22 Standard Test Method for Index of Refraction of Transparent Organic Plastics
- ASTM D5420-21 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
- ASTM D5422-17 Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer
- ASTM D5424-23a Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
- ASTM D5425-23 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products
- ASTM D5426-19 Standard Practices for Visual Inspection and Grading of Fabrics Used for Inflatable Restraints
- ASTM D5427-09(2019) Standard Practice for Accelerated Aging of Inflatable Restraint Fabrics
- ASTM D5428-08(2019) Standard Practice for Evaluating the Performance of Inflatable Restraint Modules