
【国外标准】 Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers the basic requirements and associated test methods for water-based corrosion protective zinc/aluminum dispersion inorganic basecoats, and optional sealers and topcoats for fasteners. The basecoat can contain chrome (C) or be non-chrome (NC). These coatings are applied to ferrous parts by conventional dip-spin, dip-drain, or spray methods, which can be handled through a cleaning, coating, and baking operation, and which are not adversely affected by baking temperatures up to 330 °C. The coatings are classified into six grades (Grades 1 to 6) according to the required minimum basecoat thickness, and when tested, shall conform accordingly to appearance, adhesion, corrosion resistance, blister, thread fit, and hydrogen embrittlement requirements. The coating process does not induce the possibility of internal hydrogen embrittlement provided that the fasteners have not been cleaned or pre-treated with an acid or phosphate. Alkaline cleaning or vapor degreasing is required along with shot blasting to remove rust or scale. In this specification, units are presented in the metric scale.1.1 This specification covers the basic requirements for water-based zinc/aluminum dispersion inorganic basecoats and optional sealers and topcoats for fasteners. The basecoat can contain chrome (C) or be non-chrome (NC).1.2 These coatings are applied by conventional dip-spin, dip-drain, or spray methods to ferrous parts which can be handled through a cleaning, coating, and baking operation, and which are not adversely affected by baking temperatures up to 330 °C [626 °F].1.3 The coating process does not induce the possibility of internal hydrogen embrittlement providing that the fasteners have not been cleaned or pre-treated with an acid or phosphate. Alkaline cleaning or vapor degreasing is required along with shot blasting to remove rust or scale.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F1136/F1136M-11(2019)
标准名称:
Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners
英文名称:
Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS 2805.6.1.1-2009 (R2019)/Amdt 1-2011 Electronic funds transfer - Requirements for interfaces Key management - Principles
- AS 2888.11-1993 Methods of testing plastics waste fittings Method for cyclic testing of plastics telescopic waste connectors (rubber-ring joint type)
- AS 2891.11-1991 Methods of sampling and testing asphalt Degree of particle coating
- AS 2891.11-2005 Methods of sampling and testing asphalt Degree of particle coating
- AS 3565.4-2007 (R2019)/Amdt 1-2010 Meters for water supply In-service compliance testing
- AS 3696.11-1993 Wheelchairs Test dummies
- AS 3894.11-1993 Site testing of protective coatings Equipment report
- AS 5013.11.1-2004 Food microbiology - Microbiology of food and animal feeding stuffs - Preparation of test samples, initial suspension and decimal dilutions for microbiological examination - General rules for the preparation of the initial suspension and decimal dilutions
- AS 5013.11.2-2006 Food microbiology Microbiology of food and animal feeding stuffs - Preparation of test samples, initial suspension and decimal dilutions for microbiological examination - Specific rules for the preparation of meat and meat products
- AS 5013.11.3-2006 Food microbiology Microbiology of food and animal feeding stuffs - Preparation of test samples, initial suspension and decimal dilutions for microbiological examination - Specific rules for the preparation of fish and fishery products
- AS 5013.11.3-2012 Food microbiology Microbiology of food and animal feeding stuffs - Preparation of test samples, initial suspension and decimal dilutions for microbiological examination - Specific rules for the preparation of fish and fishery products (ISO 6887-3:2003, MOD)
- AS 60034.11-2009 Rotating electrical machines Thermal protection
- AS 7240.11-2008 Fire detection and alarm systems Manual call points (ISO 7240-11:2005, MOD)
- AS IEC 60300.3.11-2011 Dependability management Application guide - Reliability centred maintenance
- AS ISO 14520.11-2009 Gaseous fire-extinguishing systems - Physical properties and system design HFC 236fa extinguishant (ISO 14520-11:2005, MOD)