
【国外标准】 Standard Test Method for Determining Plutonium by Controlled-Potential Coulometry in H2SO4 at a Platinum Working Electrode
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method is used to ascertain whether or not materials meet specifications for plutonium concentration or plutonium mass fraction.5.1.1 The materials (nuclear grade plutonium nitrate solutions, plutonium metal, plutonium oxide powder, and mixed oxide and carbide powders and pellets) to which this test method applies are subject to nuclear safeguards regulations governing their possession and use. However, adherence to this test method does not automatically guarantee regulatory acceptance of the resulting safeguards measurements. It remains the sole responsibility of the user of this test method to ensure that its application to safeguards has the approval of the proper regulatory authorities.5.1.2 When used in conjunction with appropriate certified reference materials (CRMs), this test method can demonstrate traceability to the international measurements system (SI).5.2 Fitness for Purpose of Safeguards and Nuclear Safety Application—Methods intended for use in safeguards and nuclear safety applications shall meet the requirements specified by Guide C1068 for use in such applications.5.3 A chemical calibration of the coulometer is necessary for accurate results.FIG. 1 Example of a Cell Design Used at Los Alamos National Laboratory (LANL)1.1 This test method covers the determination of milligram quantities of plutonium in unirradiated uranium-plutonium mixed oxide having a U/Pu ratio range of 0.1 to 10. This test method is also applicable to plutonium metal, plutonium oxide, uranium-plutonium mixed carbide, various plutonium compounds including fluoride and chloride salts, and plutonium solutions.1.2 The recommended amount of plutonium for each aliquant in the coulometric analysis is 5 mg to 10 mg. Precision worsens for lower amounts of plutonium, and elapsed time of electrolysis becomes impractical for higher amounts of plutonium.1.3 The quantity values stated in SI units are to be regarded as standard. The quantity values with non-SI units are given in parentheses for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 9.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1165-23
标准名称:
Standard Test Method for Determining Plutonium by Controlled-Potential Coulometry in H2SO4 at a Platinum Working Electrode
英文名称:
Standard Test Method for Determining Plutonium by Controlled-Potential Coulometry in H2SO4 at a Platinum Working Electrode标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D3964-10(2020) Standard Practice for Selection of Coating Specimens for Appearance Measurements
- ASTM D3965-21 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
- ASTM D3966/D3966M-22 Standard Test Methods for Deep Foundation Elements Under Static Lateral Load
- ASTM D3967-23 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens with Flat Loading Platens
- ASTM D3972-09(2015) Standard Test Method for Isotopic Uranium in Water by Radiochemistry
- ASTM D3974-09(2023) Standard Practices for Extraction of Trace Elements from Sediments
- ASTM D3975-93(2019) Standard Practice for Development and Use (Preparation) of Samples for Collaborative Testing of Methods for Analysis of Sediments
- ASTM D3976-22 Standard Practice for Preparation of Sediment Samples for Chemical Analysis
- ASTM D3977-97(2019) Standard Test Methods for Determining Sediment Concentration in Water Samples
- ASTM D3978-21a Standard Practice for Algal Growth Potential Testing with Pseudokirchneriella subcapitata
- ASTM D3981-09a(2016) Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications
- ASTM D3982-21 Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts
- ASTM D3983-98(2019) Standard Test Method for Measuring Strength and Shear Modulus of Nonrigid Adhesives by the Thick-Adherend Tensile-Lap Specimen
- ASTM D3984-19 Standard Specification for Ethane Thermophysical Property Tables
- ASTM D3985-17 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor