
【国外标准】 Standard Test Method for Characterizing the Performance of Refuse Size-Reduction Equipment
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Throughput, power and energy requirements, and product size are key parameters that describe the operation and performance of solid waste size-reduction equipment.5.2 This test method can be used to determine if the size-reduction equipment is operating within specifications and meeting performance criteria.5.3 Having determined the parameters given in 5.1, the equipment that has been subjected to the test may be compared to other equipment similarly tested in order to establish relative levels of performance among equipment.5.4 The basic test period is a continuous 2 to 4-h duration. The use of several test periods may be warranted to adequately assess the performance of size-reduction equipment.1.1 This test method covers measuring the performance of solid waste size-reduction equipment.1.2 This test method can be used to measure the flow (that is, throughput) of solid waste through the size-reduction equipment, energy usage of the size-reduction device, and particle size of the shredded product.1.3 This test method includes instructions for measuring energy usage, solid waste throughput, net processing time, and particle size distribution.1.4 This test method applies only to size-reduction equipment that produces a shredded product with a size corresponding to 90 % cumulative passing in the range of 0.5 to 15 cm (0.2 to 6 in.) on an air-dry weight basis. For material with nominal sizes outside of this range, the precision and bias statements for particle size designation (Section 14) may not apply.1.5 This test method can be applied to size-reduction equipment located anywhere within a processing line.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6.1 Exception—The values given in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 7 for specific hazard information.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM E959-83(2018)
标准名称:
Standard Test Method for Characterizing the Performance of Refuse Size-Reduction Equipment
英文名称:
Standard Test Method for Characterizing the Performance of Refuse Size-Reduction Equipment标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E2601-23 Standard Practice for Radiological and Nuclear Emergency Response
- ASTM E2606-18 Standard Practice for Receipt Notification as a Result of Tangible Asset Movement
- ASTM E2607-21 Standard Practice for Cannibalization/Reclamation of Serviceable Equipment Components to Support Demand Requirements
- ASTM E2608-20 Standard Practice for Equipment Control Matrix (ECM)
- ASTM E261-16(2021) Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
- ASTM E2611-19 Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method
- ASTM E2614-15(2020)e1 Standard Guide for Evaluation of Cleanroom Disinfectants
- ASTM E2616-09(2020) Standard Guide for Remedy Selection Integrating Risk-Based Corrective Action and Non-Risk Considerations
- ASTM E2617-17 Standard Practice for Validation of Empirically Derived Multivariate Calibrations
- ASTM E2619/E2619M-17 Standard Practice for Measuring and Calculating Building Loss Features That Take Up Floor Area in Buildings
- ASTM E2624-17 Standard Practice for Torque Calibration of Testing Machines
- ASTM E2625-19 Standard Practice for Controlling Occupational Exposure to Respirable Crystalline Silica for Construction and Demolition Activities
- ASTM E2627-13(2019) Standard Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials
- ASTM E2635-22 Standard Practice for Water Conservation in Buildings Through In-Situ Water Reclamation
- ASTM E2637-17 Standard Guide for Utilizing the Environmental Cost Element Structure Presented by Classification