
【国外标准】 Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
4.1 These test methods provide a means of measuring the total compressive deflection of chemical-resistant, machinery-grout materials under a sustained load at the test temperature. Test stress and temperature can be selected to simulate anticipated use conditions. For the purposes of these tests, creep is considered to be the compressive deflection in cm per cm [inches per inch], which occurs after the initial loading of the specimen at laboratory temperature. The results do not necessarily correlate for different specimen thicknesses. No correlation has been established to actual-use conditions.1.1 These test methods cover a quantitative, comparative test for compressive creep of chemical-resistant grouting materials under a sustained load at a test temperature. Constant load is maintained using a bolt and spring washers. Measurements are made at laboratory temperature after exposure periods at the selected test temperature.1.2 Test Method A outlines the molding techniques for an unbonded test specimen. Test Method B covers the molding techniques for a bonded test specimen.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1181/C1181M-17
标准名称:
Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts
英文名称:
Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D202-23 Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
- ASTM D2028/D2028M-15(2021)e1 Standard Specification for Cutback Asphalt (Rapid-Curing Type)
- ASTM D2036-09(2022) Standard Test Methods for Cyanides in Water
- ASTM D204-02(2021) Standard Test Methods for Sewing Threads
- ASTM D2050-23 Standard Terminology Relating to Fastener Subassemblies Used in the Manufacture of Textiles
- ASTM D2052-05(2022) Standard Test Method for Colorfastness of Zippers to Drycleaning
- ASTM D2060-14(2022) Standard Test Methods for Measuring Zipper Dimensions
- ASTM D2062-03(2021) Standard Test Methods for Operability of Zippers
- ASTM D2065-03(2017) Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant Accelerated Moisture Stress
- ASTM D2074-07(2019) Standard Test Methods for Total, Primary, Secondary, and Tertiary Amine Values of Fatty Amines by Alternative Indicator Method
- ASTM D209-81(2023) Standard Specification for Lampblack Pigment
- ASTM D2091-96(2024) Standard Test Method for Print Resistance of Lacquers
- ASTM D2093-03(2017) Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding
- ASTM D2094-00(2023) Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests
- ASTM D2097-03(2023) Standard Test Method for Flex Testing of Finish on Upholstery Leather