
【国外标准】 Standard Specification for Copper-Beryllium Alloy Rod and Bar
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification establishes the requirements for rods and bars in straight lengths of copper-beryllium alloys with Copper Alloy UNS Nos. C17000, C17200, and C17300. The material for manufacture shall be cast and worked to such purity and soundness as to be suitable for processing by hot working, cold working, and annealing to produce a uniform wrought structure and specified temper in the finished product. Products shall be available in the following tempers: solution heat-treated TB00 (A), and cold-drawn hard TD04 (H), which shall be precipitation heat treated after machining or forming. Products that are already precipitation heat treated by the manufacturer shall be available in tempers TF00 (AT) and TH04 (HT). Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (diameter, length, straightness, and edge contour), mechanical (tensile and yield strength, Rockwell hardness, and elongation), and chemical composition requirements.1.1 This specification establishes the requirements for copper-beryllium alloy rod and bar in straight lengths. The following three alloys are included:Copper AlloyUNS No. Previously UsedDesignations Nominal BerylliumContent, % C17000 Alloy 165 1.7C17200 Alloy 25 1.9C17300 1.9 +0.4 lead1.2 Unless otherwise required, Copper Alloy UNS No. C17200 shall be the alloy furnished whenever Specification B196/B196M is specified without any alloy designation.1.3 The values stated in either inch-pounds or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM B196/B196M-18
标准名称:
Standard Specification for Copper-Beryllium Alloy Rod and Bar
英文名称:
Standard Specification for Copper-Beryllium Alloy Rod and Bar标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E2102-21 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
- ASTM E2103/E2103M-19 Standard Classification for Bridge Elements—UNIFORMAT II
- ASTM E2104-22 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
- ASTM E2106-00(2019) Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses
- ASTM E2107-20 Standard Practice for Environmental Regulatory Compliance Audits
- ASTM E2108-16 Standard Practice for Calibration of the Electron Binding-Energy Scale of an X-Ray Photoelectron Spectrometer
- ASTM E2109-01(2021) Standard Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings
- ASTM E211-82(2022) Standard Specification for Cover Glasses and Glass Slides for Use in Microscopy
- ASTM E2110-17 Standard Terminology for Exterior Insulation and Finish Systems (EIFS)
- ASTM E2112-23 Standard Practice for Installation of Exterior Windows, Doors and Skylights
- ASTM E2113-23 Standard Test Method for Length Change Calibration of Thermomechanical Analyzers
- ASTM E2114-23 Standard Terminology for Sustainability
- ASTM E2115-22 Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities
- ASTM E2121-21 Standard Practice for Installing Radon Mitigation Systems in Existing Low-Rise Residential Buildings
- ASTM E2122-22 Standard Guide for Conducting In-situ Field Bioassays With Caged Bivalves