
【国外标准】 Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 This test method is used to assess in situ strength of undisturbed soil and compacted materials (or both). The penetration rate of the 8 kg [17.6 lb] DCP can be used to estimate in situ CBR (California Bearing Ratio), to identify strata thickness, shear strength of strata, and other material characteristics.5.1.1 Other test methods exist for DCPs with different hammer weights and cone tip sizes, which have correlations that are unique to the instrument, such as Test Method D7380/D7380M.5.2 The 8 kg [17.6 lb] DCP is held vertically, and therefore is typically used in horizontal construction applications, such as pavements and floor slabs.5.3 This instrument is typically used to assess material properties down to a depth of 1000 mm [39 in.] below the surface. The penetration depth can be increased using drive rod extensions. However, if drive rod extensions are used, care should be taken when using correlations to estimate other parameters, since these correlations are only appropriate for specific DCP configurations. The mass and inertia of the device will change and skin friction along drive rod extensions will occur.5.4 The 8 kg [17.6 lb] DCP can be used to estimate the strength characteristics of fine and coarse-grained soils, granular construction materials, and weak stabilized or modified materials. The 8 kg [17.6 lb] DCP cannot be used in highly stabilized or cemented materials or for granular materials containing a large percentage of aggregates greater than 50 mm [2 in.].5.5 The 8 kg [17.6 lb] DCP can be used to estimate the strength of in situ materials underlying a bound or highly stabilized layer by first drilling or coring an access hole.NOTE 1: The DCP may be used to assess the density of a fairly uniform material by relating density to penetration rate on the same material. In this way, undercompacted or “soft” spots can be identified, even though the DCP does not measure density directly.35.6 A field DCP measurement results in a field or in situ CBR and will not normally correlate with the laboratory or soaked CBR of the same material. The test is thus intended to evaluate the in situ strength of a material under existing field conditions.1.1 This test method covers the measurement of the penetration rate of the dynamic cone penetrometer with an 8 kg [17.6 lb] hammer (8 kg [17.6 lb] DCP) through undisturbed soil or compacted materials, or both. The penetration rate may be related to in situ strength such as an estimated in situ CBR (California Bearing Ratio). A soil density may be estimated (Note 1) if the soil type and moisture content are known. The DCP described in this test method is typically used for pavement applications.1.2 The test method provides for an optional 4.6 kg [10.1 lb] sliding hammer when the use of the 8 kg [17.6 lb] sliding mass produces excessive penetration in soft ground conditions.1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D6951/D6951M-18(2023)
标准名称:
Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications
英文名称:
Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D6950/D6950M-04(2012)e1 Standard Practice for Application of Heat Weldable Atactic Polypropylene (APP) Modified Bituminous Waterproofing Membranes Systems for New Building Decks (Withdrawn 2015)
- 下一篇: ASTM D6953-18 Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC)
- 推荐标准
- ASTM 51026-23 Standard Practice for Using the Fricke Dosimetry System
- ASTM 52303-24 Standard Guide for Absorbed-Dose Mapping in Radiation Processing Facilities
- ASTM A1-00(2018) Standard Specification for Carbon Steel Tee Rails
- ASTM A1000/A1000M-17(2023) Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality
- ASTM A1001-18 Standard Specification for High-Strength Steel Castings in Heavy Sections
- ASTM A1002-16(2020) Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
- ASTM A1004/A1004M-99(2018) Standard Practice for Establishing Conformance to the Minimum Expected Corrosion Characteristics of Metallic, Painted-Metallic, and Nonmetallic-Coated Steel Sheet Intended for Use as Cold Formed Framing Members
- ASTM A1009-18 Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM A101-04(2019) Standard Specification for Ferrochromium
- ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
- ASTM A1012-10(2021) Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins
- ASTM A1015-01(2018) Standard Guide for Videoborescoping of Tubular Products for Sanitary Applications
- ASTM A1016/A1016M-23 Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
- ASTM A102-04(2019) Standard Specification for Ferrovanadium
- ASTM A1021/A1021M-20 Standard Specification for Martensitic Stainless Steel Forgings and Forging Stock for High-Temperature Service