
【国外标准】 Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
1.1 This specification addresses mechanically attached polymeric roof underlayment used in steep slope roofing.1.2 The objective of this specification is to provide a finished product that will be used as a water-shedding underlayment layer on steep sloped roofs prior to and after installation of the primary roof covering.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8257/D8257M-22
标准名称:
Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing
英文名称:
Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 其它标准
- 上一篇: ASTM D8256-23 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
- 下一篇: ASTM D8259/D8259M-21 Standard Test Method for Rotary Wheel Testing (RWT) of Compacted Asphalt Mixtures
- 推荐标准
- AS 1038.22-2000 (R2013) Coal and coke - Analysis and testing Higher rank coal - Mineral matter and water of constitution
- AS 1301.P201m-1986 Methods of test for pulp and paper (metric units) Kappa number of pulp
- AS 1301.P414m-1986 Methods of test for pulp and paper (metric units) Conditioning of paper for testing
- AS 1774.22-1985 Refractories and refractory materials - Physical test methods Bonding strength of refractory mortar
- AS 1807.22-1989 Cleanrooms, workstations and safety cabinets - Methods of test Determination of air barrier containment of laminar flow safety cabinets
- AS 2001.2.22-1986 Methods of test for textiles Physical tests - Determination of yarn slippage in woven fabrics at a standard stitched seam
- AS 2362.22-1993 Automatic fire detection and alarm systems - Methods of test for actuating devices Sound pressure level test
- AS 2400.22-1985 Packaging Closures
- AS 3730.22-1993 Guide to the properties of paints for buildings Concrete and masonry sealer - Solvent-borne - Interior/exterior
- ASTM D7208-23 Standard Test Method for Determination of Temporary Ditch Check Performance in Protecting Earthen Channels from Stormwater-Induced Erosion
- ASTM D7210-21 Standard Practice for Extraction of Additives in Polyolefin Plastics
- ASTM D7212-13(2018) Standard Test Method for Low Sulfur in Automotive Fuels by Energy-Dispersive X-ray Fluorescence Spectrometry Using a Low-Background Proportional Counter
- ASTM D7215-22 Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels
- ASTM D7216-23 Standard Test Method for Determining Automotive Engine Oil Compatibility with Typical Seal Elastomers
- ASTM D7219-19 Standard Specification for Isotropic and Near-isotropic Nuclear Graphites