
【国外标准】 Standard Consumer Safety Specification for Infant Bath Tubs
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers the performance requirements, test methods, and labeling requirements to promote the safe use of infant bath tubs. The performance requirements; restraint system, static load, suction cups requirements shall be discussed. Locking mechanism, protective components, torque, label permanence, warning permanence, static load, and suction cup shall be tested to meet the requirements prescribed.1.1 This consumer safety specification establishes performance requirements, test methods, and labeling requirements to promote the safe use of infant bath tubs. It also covers slings, pads, inserts, and similar accessories when such accessories are used with the infant bath tub.1.2 This consumer safety specification is intended to reduce the risk of death and minimize injury to infants resulting from use and reasonably foreseeable abuse of infant bath tubs and infant bath tub accessories.1.3 No infant bath tub or infant bath tub accessory produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F2670-22
标准名称:
Standard Consumer Safety Specification for Infant Bath Tubs
英文名称:
Standard Consumer Safety Specification for Infant Bath Tubs标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E2601-23 Standard Practice for Radiological and Nuclear Emergency Response
- ASTM E2606-18 Standard Practice for Receipt Notification as a Result of Tangible Asset Movement
- ASTM E2607-21 Standard Practice for Cannibalization/Reclamation of Serviceable Equipment Components to Support Demand Requirements
- ASTM E2608-20 Standard Practice for Equipment Control Matrix (ECM)
- ASTM E261-16(2021) Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
- ASTM E2611-19 Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method
- ASTM E2614-15(2020)e1 Standard Guide for Evaluation of Cleanroom Disinfectants
- ASTM E2616-09(2020) Standard Guide for Remedy Selection Integrating Risk-Based Corrective Action and Non-Risk Considerations
- ASTM E2617-17 Standard Practice for Validation of Empirically Derived Multivariate Calibrations
- ASTM E2619/E2619M-17 Standard Practice for Measuring and Calculating Building Loss Features That Take Up Floor Area in Buildings
- ASTM E2624-17 Standard Practice for Torque Calibration of Testing Machines
- ASTM E2625-19 Standard Practice for Controlling Occupational Exposure to Respirable Crystalline Silica for Construction and Demolition Activities
- ASTM E2627-13(2019) Standard Practice for Determining Average Grain Size Using Electron Backscatter Diffraction (EBSD) in Fully Recrystallized Polycrystalline Materials
- ASTM E2635-22 Standard Practice for Water Conservation in Buildings Through In-Situ Water Reclamation
- ASTM E2637-17 Standard Guide for Utilizing the Environmental Cost Element Structure Presented by Classification