
【国外标准】 Standard Test Method for Splitting Tensile Strength of Masonry Units
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Masonry units alone and within assemblages commonly fail in a tensile mode when loaded in compression to failure. These tensile stresses result from differences in modulus of elasticity and Poisson's ratio between the masonry unit and mortar. Additionally, the dissimilarity in behavior of the grout within cores of masonry units under load leads to tensile stresses in the units and results in a splitting failure.5.2 This test method produces a line load along the bed surface of the masonry unit. The compressive load applied to the unit, imposed by means of bearing rods, results in a tensile stress distributed over the height of the unit for the split length of the unit. This test method can be conducted with the rod oriented either in the longitudinal direction or in the transverse direction of the bed face. The splitting tensile strength is calculated by the equation given in 10.1.5.3 The test value provides an indicator of masonry-unit splitting tensile strength. Additionally, the presence of defects such as visible voids or impurities in masonry units may be revealed.5.4 The moisture content of the specimen will affect test results.5.5 The height of the specimen will affect test results.1.1 This test method covers the determination of the splitting tensile strength of masonry units.1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1006/C1006M-20a
标准名称:
Standard Test Method for Splitting Tensile Strength of Masonry Units
英文名称:
Standard Test Method for Splitting Tensile Strength of Masonry Units标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4399-05(2023) Standard Test Method for Measuring Electrical Conductivity of Electrocoat Baths
- ASTM D4404-18 Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry
- ASTM D4414-95(2020) Standard Practice for Measurement of Wet Film Thickness by Notch Gages
- ASTM D4416-09(2023) Standard Specification for Acrylic Acid
- ASTM D4417-21 Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
- ASTM D4418-22 Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines
- ASTM D4422-19 Standard Test Method for Ash in Analysis of Petroleum Coke
- ASTM D4426-01(2021) Standard Test Method for Determination of Percent Nonvolatile Content of Liquid Phenolic Resins Used for Wood Laminating
- ASTM D4437/D4437M-16(2023) Standard Practice for Nondestructive Testing (NDT) for Determining the Integrity of Seams Used in Joining Flexible Polymeric Sheet Geomembranes
- ASTM D4439-23b Standard Terminology for Geosynthetics
- ASTM D444-88(2020) Standard Test Methods for Chemical Analysis of Zinc Yellow Pigment (Zinc Chromate Yellow)
- ASTM D4440-23 Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology
- ASTM D4441-20 Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene
- ASTM D4444-13(2018) Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
- ASTM D4445-23 Standard Test Method for Fungicides for Controlling Sapstain and Mold on Unseasoned Lumber (Laboratory Method)