
【国外标准】 Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 Asphalt prisms compacted with the shear box compactor can be used to obtain specimens for further testing, including bulk specific gravity following Test Methods D6752/D6752M and D2726/D2726M; dynamic modulus following AASHTO T 342; dynamic modulus, flow number, and flow time following AASHTO T 378; and fatigue performance characteristics following AASHTO T 321.5.2 Specimens to perform other standard tests could also be obtained, as long as their volume is contained within the volume of a prism having maximum width, length, and height (W × L × H) of 150 mm, 450 mm, and 185 mm, respectively. The maximum prism height depends on the mix type, the target air voids, and the equipment limitations.NOTE 1: The aggregate orientation in the samples produced by this method may be different from samples produced by other laboratory compaction methods. This should be considered when comparing mechanical test results from different compaction methods.NOTE 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors. Following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.1.1 This practice covers the fabrication of prismatic specimens of asphalt mixture using the shear box compactor (SBC). Compacted specimens are suitable for volumetric and physical property testing. This standard practice should not be used for acceptance or rejection of a material or for purchasing purposes.1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard with exception of degrees (°) where angle is specified.1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D7981-20
标准名称:
Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor
英文名称:
Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D4713-12(2020) Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
- ASTM D4716/D4716M-22 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
- ASTM D4718/D4718M-15(2023) Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
- ASTM D4724/D4724M-21 Standard Test Method for Entanglements in Filament Yarns by Needle Insertion
- ASTM D4727/D4727M-22 Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes
- ASTM D4728-17(2022) Standard Test Method for Random Vibration Testing of Shipping Containers
- ASTM D4734-20 Standard Specification for Refined Benzene-545
- ASTM D4740-20 Standard Test Method for Cleanliness and Compatibility of Residual Fuels by Spot Test
- ASTM D4748-10(2020) Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar
- ASTM D476-15(2021) Standard Classification for Dry Pigmentary Titanium Dioxide Products
- ASTM D4761-19 Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials
- ASTM D4762-23 Standard Guide for Testing Polymer Matrix Composite Materials
- ASTM D4763-06(2020) Standard Practice for Identification of Chemicals in Water by Fluorescence Spectroscopy
- ASTM D4764-01(2023) Standard Test Method for Determination by X-ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint
- ASTM D4765-13(2018) Standard Test Method for Measurement of Fluorides in Workplace Atmospheres by Ion-Selective Electrodes