【国外标准】 Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 The test method is to be used to determine the abrasion resistance or mechanical durability of thin omniphobic or thin hydrophobic coatings. These coatings are often used to enhance the surface’s value by promoting fingerprint resistance, water removal, stain resistance, and easy-clean properties. A comparison of the contact angle and the depreciation of that contact angle due to exposure to mechanical abrasion determines the coating’s ability to remain effective after exposure to environmental abrasion.5.1.1 The test method is used to appraise the removal of thin films when gravimetric measurements will not yield a detectable change in film mass due to the small amount of material comprising these films, which are on the order of nanometers thick.5.1.2 Only fully cured specimens are evaluated unless otherwise specified and agreed upon by the interested parties.5.2 Different coating materials may be evaluated for relative durability by evaluating abrasion cycles versus water contact angle using this method.5.3 Different curing or conditioning methods may be evaluated by preparing test specimens with the same coating and then evaluating abrasion resistance using this method.1.1 This test method describes a procedure for evaluating dry abrasion resistance of a thin hydrophobic or omniphobic coating, or both. The coating is typically less than 100 nm thick and is applied to a planar, glass substrate by application methods including, but not limited to, physical vapor deposition (PVD), dip, or spray.1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard with the exception of angular measurement which are reported in degrees.NOTE 1: This test method measures a static contact angle and is not equivalent to Test Method C813 which measures an advancing contact angle.NOTE 2: Test Method D4060 is not applicable to hydrophobic and omniphobic coatings because the molecular monolayer does not generally result in a detectable weight change to the specimen after subjecting it to abrasion.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8380-21
标准名称:
Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings
英文名称:
Standard Test Method for Dry Abrasion Resistance of Hydrophobic and Omniphobic Coatings标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard