
【国外标准】 Standard Specification for Structural Silicone Sealants
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems. Sealants shall be classified as to types and uses: Type S; Type M; Use G; and Use O. The physical, mechanical, and performance properties of the sealant shall conform to the requirements described. The following test methods shall be performed: rheological properties; extrudability; hardness; heat aging; tack-free time; tensile adhesion; and shelf life.1.1 This specification covers the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems.1.2 Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification. Additional properties may be added as ASTM test methods for those properties become available.1.3 The values stated in metric (SI) units are to be regarded as the standard. The values in parentheses are for information only.1.4 Committee C24, with jurisdiction over this specification, is aware of two comparable standards by other organizations: ETAG No. 002 and the Chinese national standard GB16776.NOTE 1: ETAG 002 is currently no longer supported.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1184-23
标准名称:
Standard Specification for Structural Silicone Sealants
英文名称:
Standard Specification for Structural Silicone Sealants标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM A646/A646M-17(2022) Standard Specification for Premium Quality Alloy Steel Blooms and Billets for Aircraft and Aerospace Forgings
- ASTM A648-18 Standard Specification for Steel Wire, Hard-Drawn for Prestressed Concrete Pipe
- ASTM A649/A649M-10(2020) Standard Specification for Forged Steel Rolls Used for Corrugating Paper Machinery
- ASTM A650/A650M-18 Standard Specification for Tin Mill Products, Black Plate, Double Reduced
- ASTM A660/A660M-21 Standard Specification for Centrifugally Cast Carbon Steel Pipe for High-Temperature Service
- ASTM A662/A662M-17 Standard Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service
- ASTM A663/A663M-23 Standard Specification for Steel Bars, Carbon, Merchant Quality, Mechanical Properties
- ASTM A666-23 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
- ASTM A668/A668M-23 Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use
- ASTM A673/A673M-17 Standard Specification for Sampling Procedure for Impact Testing of Structural Steel
- ASTM A677-16(2023) Standard Specification for Nonoriented Electrical Steel Fully Processed Types
- ASTM A681-08(2022) Standard Specification for Tool Steels Alloy
- ASTM A683-16(2023) Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types
- ASTM A693-22 Standard Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
- ASTM A694/A694M-16(2022) Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service